Samsung SMT-i5343 User Manual Download

Page: 78 / 201

Outbound Call Lock

Select

[Menu]



[Call Service]



[Outbound Call Lock]

- When this service is enabled, an outgoing call

is restricted.

If you enable this service by using the
navigation button and enter a password,
an outgoing call is restricted.
When you press the

[OK]

soft button in

the below popup window, it becomes Call
Waiting status.

- You can disable the service in the same

manner.

Wake-Up Call

Select

[Menu]



[Call Service]



[Wake-Up Call]

You can enable this service using the
navigation button and set the repeat
setting to either at one specific time or
everyday. When you press the below

[Save]

soft button, wake-up call is

enabled.

- Repeat Setting

[Once]

: When you enter month,

date, hour, and minute, the wake-up call rings
once at the specified time. (e.g. 06181500-June
18 3:00 pm)

- Repeat Setting

[Repeat]

: When you enter hour

and minute,the wake-up call rings every day at
the specified time. (e.g. 1502-3:02 pm)

Summary of Contents for SMT-i5343










































































































































































































Search results

Summary of Contents for SMT-i5343

Reviews:

Related manuals for SMT-i5343

Brands by name

Popular brands

Samsung SMT-i5343, User Manual

Search results

Summary of Contents for SMT-i5343

Reviews:

Related manuals for SMT-i5343

Brands by name

Popular brands