Samsung SMT-i5343 User Manual Download

Page: 77 / 201

SMT-i5343 User Guide _

Call Waiting

Select

[Menu]



[Call Service]



[Call Waiting]

- When the Call Waiting is enabled, you can

receive a new incoming call by making a
current call standby.

When you press the

[OK]

soft button in

the below popup window, it becomes Call
Waiting status.

- You can disable the service in the same

manner.

Absence

Select

[Menu]



[Call Service]



[Absence]

- When the absence is enabled, your absence is

notified to a caller when there is an incoming
call.

When you press the

[OK]

soft button in

the below popup window, it becomes
absence status.

- You can disable the service in the same

manner.

Summary of Contents for SMT-i5343










































































































































































































Search results

Summary of Contents for SMT-i5343

Reviews:

Related manuals for SMT-i5343

Brands by name

Popular brands

Samsung SMT-i5343, User Manual

Search results

Summary of Contents for SMT-i5343

Reviews:

Related manuals for SMT-i5343

Brands by name

Popular brands