Samsung SMT-i5343 User Manual Download

Page: 62 / 201

History

The recently incoming/outgoing calls, incoming calls during absence and all the
received/sent messages are displayed. Up to 500 records can be saved.

Select

[Menu]



[History]

. By using the navigation button, you can move to

Total/Received/Sent/Absence/Message.

[All]

: The recently sent/received calls and messages are displayed.

[Inbox]

: The recently received calls and messages are displayed.

[Outbox]

: The recently sent calls and messages are displayed.

[Missed]

: The list of received calls during absence is displayed.

[Message]

: The recently sent/received messages are displayed.

- If you move to a desired phone number by using the navigation button and press either the

[OK]

button or the right selection button, the detail information is retrieved.

Summary of Contents for SMT-i5343










































































































































































































Search results

Summary of Contents for SMT-i5343

Reviews:

Related manuals for SMT-i5343

Brands by name

Popular brands

Samsung SMT-i5343, User Manual

Search results

Summary of Contents for SMT-i5343

Reviews:

Related manuals for SMT-i5343

Brands by name

Popular brands