Samsung SMARTCAM SNH-E6440BN, User Manual, Page: 47 / 88

Wi-Fi Direct connection
M

You can only use it in a camera that has a Wi-Fi Direct sticker
attached to it.

Press the button, " Tap here to add registered camera " when you
register a camera being used in another account, in order to register
it immediately without setting it.
7. Tap < Wireless Setup >.
8. Tap < Next > after connecting
a camera according to the
instructions displayed on the
screen.
9. After selecting a camera to
connect, tap <
Next >.
M

Select a camera that has the last
four digits of the serial number on
the back of the product.
10. Select a WiFi router connected to
your camera.
• : After entering the
password, connect to a WiFi
router.
• : Without the password, you
will not be connected to a WiFi
router.
• Other WiFi Networks : Enter the
SSID name, security type and
password.
If selected, it shows guide
on SSID and networking
procedures.
• Network password :
If you select a WiFi router with
the password, then the pop up
window will prompt you to enter
the password.
11. The LED of the camera will
turn into green if a camera is
connected to Wi-Fi.
M

Camera's LED will blink in blue
while searching for a WiFi router.
If a connection is made to the WiFi
router, the LED will be blue
consistently. After a short while,
while the camera is connecting to
the server, the LED will turn green.
12. Enter < Camera Name > and
< Camera password > and then
click < OK >.
M

Click < Show Password > to check
your password.
13. The camera registration is
completed.
Select <
Yes > for a camera
setting.
Select <
No > to view a live
screen.
M

If you failed to register wirelessly,
please try again over a wireline.

Cameras may not be registered
depending on the settings of the
mobile device.
In this case, contact the service
center.
00 : 02
Please wait until the status LED on the
camera changed from blue to green.
It takes about 3 minutes.
Registration
Registration
Other WiFi Networks
Select the WiFi network you
want the camera to connect to.
Apple Network 8dfdc7
design
Cisco_WPS_57090
KT12580
NETGEAR27
W
iF
i
DIREC
T
Is there a WiFi DIRECT sticker on
the camera lens?
If yes, select Wireless Setup.
If not, select Optional Setup.
Wireless
Setup
Optional
Setup
Tap here to add registered camera
Registration
The camera(s) will be listed below.
Select the camera you wish to add and
tap <Next>.
If a camera doesn't connect, please
check '?'.
Next
DCIN 5V DCIN 5V
Next
Registration
1
Plug in the power adapter
and connect it to the
camera. Camera can take
up to 2 minutes to boot up.
2
When the camera LED flashes in
red, press the WiFi button on the
back of the camera for 5 seconds.
3
The status LED on the
camera will change to light
green/yellow. Tap <Next>
Registration
WIFI ( )
Select the WiFi network you
want the camera to connect to.
Apple Network 8dfdc7
design
Cisco_WPS_57090
KT12580
NETGEAR27
Registration
Select the WiFi network you
want the camera to connect to.
Apple Network 8dfdc7
design
Cisco_WPS_57090
KT12580
NETGEAR27
q
1
w
2
e
3
r
4
t
5
y
6
u
7
i
8
o
9
p
0
a s d f g h j k l
z x c v b n m
123
Sym
···
?
English(US)
.
···
Done
Cancel OK
Network password
Enter WiFi network password
00 : 02
Please wait until the status LED on the
camera changed from blue to green.
It takes about 3 minutes.
Registration Registration
00 : 02
Please wait until the status LED on the
camera changed from blue to green.
It takes about 3 minutes.
OK Cancel
Camera Name
Camera password
Show Password
Example: Living Room
Use 1 - 8 numbers and/or letters
Confirm password
Create camera name and camera password.
No Yes
Camera registered
successfully.
The camera settings can be set
to your preference. Continue
with the camera setup?