COLOR DOME CAMERA
User Guide
28
COLOR DOME CAMERA
User Guide
29
SID-562(W)N
SID-562(W)P
ELECTRICAL
Input Voltage
AC 24V / DC 12V
Power Consumption
Max 3.5W
VIDEO
Imaging Device
Diagonal 6mm (1/3") Sony DS CCD
Total Pixels
811(H) x 508(V)
795(H) x 596(V)
Effective Pixels
768(H) x 494(V)
752(H) x 582(V)
Scanning System
2:1 Interlace
Synchronization
Internal / Line Lock
Frequency
H : 15.734KHz / V : 59.94Hz
H : 15.625KHz / V : 50.00Hz
Horizontal Resolution
Color : 560TV lines (Min.) / B/W : 700TV lines (Min.)
Min. Illumination
Color : 0.3Lux (50 IRE @F1.2), 0.001Lux (SENS-UP x256)
S/N (Y Signal)
52dB
Video Output
CVBS : 1.0Vp-p / 75Ω
LENS
Zoom Ratio
3.6x (Manual)
Focal length
2.8 ~ 10.0mm (F1.2)
Min. Objecy Distance
1:1.2(Wide) ~ 2.8(Tele)
PAN / TILT / ROTATE
Pan / Tilt / Rotate Range
0° ~ 340° / 0° ~ 146° / 0° ~ 340°
OPERATIONAL
Electronic Shutter Speed
ESC (1/60 ~ 1/120,000sec) / Manual / A.FLK
ESC (1/50 ~ 1/120,000sec) / Manual / A.FLK
On Screen Display
NTSC : Korean, English, Spanish, Japanese, French, Portuguese
PAL : English, French, German, Spanish, Italian, Chinese, Portuguese
Backlight Compensation
WDR(52dB) / BLC / HLC / Off
Day & Night
COLOR / B/W / AUTO (Electrical)
Gain Control
Low / High / Off
White Balance
ATW / AWC / Manual / Indoor / Outdoor
SENS-UP (frame Integration)
Auto / Off (Selectable limit x2~ x256)
Motion Detection
On / Off (8 Programmable zones)
Privacy Masking
On / Off (8 Programmable zones)
3D Noise Filter (SSNRII)
On / Off (1 ~ 32 Level)
Digital Zoom
On / Off (x2 ~ x10)
Digital Image Stabilization(DIS)
On / Off
Sharpness
On / Off
Camera Title
On / Off
Flip / Mirror
On / Off
Communication
RS-485 (Baudrate 2400, 4800, 9600, 19200, 38400, 57600 bps Selectable)
Protocol
Samsung Techwin protocol, Pelco-D protocol
ENVIRONMENTAL
Operating Temperature / Humidity
-10°C ~ +50°C / 20% ~ 80% RH
MECHANICAL
Dimension / Weight
Ø141.2 x 105.5mm / 545g
※
SID-562WN, SID-562WP : Ivory color base model
Refer to the following table if you are experiencing trouble with your camera.
Contact an authorized technician if the table does not provide you with a
solution to the trouble.
* RS-485 Communication establishment initial value
Item
Camera ID
BAUD RATE UART MODE
RET PKT
Initial value
1
9600
8-NONE-1
ENABLE
485 Control Board Connection Port
RS-485 Control Port
(+) CONNECTION TERMINAL (TRX+)
485+
( - ) CONNECTION TERMINAL (TRX-)
485-
●
Nothing appears on the screen.
▶
Check that the power cord and line connection between the camera and monitor are fixed properly.
▶
Check that you have properly connected VIDEO cable to the camera VIDEO output jack.
●
The image on the screen is dim.
▶
Is lens stained with dirt? Clean your lens with soft, clean cloth.
▶
Set the monitor or DVR to proper condition.
▶
If the camera is exposed to too strong light, change the camera position.
●
The image on the screen is dark.
▶
Adjust the contrast feature of the monitor or DVR.
▶
If you have an intermediate device, set the 75
Ω
/ Hi-z properly.
●
The camera is not working properly, and the surface of the camera is hot.
▶
Check that you have properly connected the camera to an appropriate power source.
●
The DAY/NIGHT menu does not work.
▶
Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
●
The SENS-UP function does not work.
▶
Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
▶
Check that SHUTTER of EXPOSURE SETUP menu is 'A.FLK'.
●
The Motion Detection function does not work.
▶
Check that MOTION DET of SPECIAL SETUP menu is ‘OFF’.
●
Color is not correct.
▶
Check the setting of WHITE BAL SETUP menu .
●
The screen flickers continually.
▶
Check that direction of camera turns toward the Sun.
●
RS-485 communication fails.
▶
Check the polarity between RS-485 Control Port and RS-485 cable.
▶
Check the RS-485 Communication establishment initial value
▶
We recommend that you make ground connect between camera and controller in order to maintain
safety communication control.
Troubleshooting
Specifications