Samsung SHC-721N Instruction Manual Download Page 22

COLOR CCD CAMERA

User’s Manual

43

COLOR CCD CAMERA

User’s Manual

42

Problem

Motion Detection
function is not active.

The color of the picture
is not matched.

The image on the screen
flickers.

L/L mode isn’t able to
be selected.

Solution

• Have  you set ‘Motion Det.’ menu to OFF?
• Have  you set ‘MD Level’ to too low?
• Have  you set ‘MD Area’ properly?

• Check that you have properly set the ‘White Bal.’

menu.

• Is the camera facing to direct sunlight or fluoresent

lighting? Change the camera position.

• Are you using Auto Iris Lens? Check that you have

properly connected the lens plug to the Auto Iris
connector on the side of the camera.

• Have  you connected your camera to DC power

source? Connect it to AC power source.

Troubleshooting

Specifications

Item

Power Source

Power Consumption

Image Sensor

Total Pixels

Effective Pixels

Scanning System

Synchronization

Video Output

Resolution

Wide Dynamic Range

Day & Night

Gain Control

Electronic Shutter Speed

Sense up

Iris Mode

White Balance

Min. Illumination

S/N (Y signal)

RS-232C

Motion Detection

O.S.D

DNR

Privacy Function

Timer

Lens Mount

Operating Temperature

Operating Humidity

Dimension (mm)

Weight (W/O Lens & Power Cord)

280mA (DC) / 3.8 W (AC)                                           3.8W

1/3", Vertical double density interline CCD

Internal / Line Lock

1.0V[p-p] NTSC Composite, 75

/ BNC Connector        1.0V[p-p] PAL Composite, 75

/ BNC Connector

500Lines (color) / 550Lines (B/W)

Built-in (46dB)

ON / OFF / AUTO 1 / AUTO 2 (Filter Auto Change)

AGC-L, AGC-H, OFF  Selectable

1/60~1/200,000sec (Auto / Manual)        1/50~1/200,000sec (Auto / Manual)

Built-in (selectable limit~X128)

ESC / Video Drive / DC Drive

W-ATW / S-ATW / H-ATW / L-ATW / AWC / Manual

Color: 0.8lux at F1.2, B/W: 0.01lux at F1.2

50dB (AGC Off)

Built-in

MD1 / MD2 / OFF (Built-in Alarm Output Connector)

Built-in

Low / High selectable

ON / OFF (4 Programmable Zone)

Built-in (24Hour, Not Memoring)

C / CS Mount

-10°C ~ +50°C (14°F ~ 122°F)

30% ~ 90% RH

69(W) X 56(H) X 125(D) without mounting foot & connector

460g                                                     500g

SHC-721P

SHC-721PH

SHC-721N

DC 12V / AC 24V compatible

AC 230V / 50Hz

811(H) x 508(V), 1/3" CCD

768(H) x 494(V), 1/3" CCD

2:1 Interlaced 525 Lines/60 Fields/30 Frames 

795(H) x 596(V), 1/3" CCD

752(H) x 582(V), 1/3" CCD

2:1 Interlaced 625 Lines/50 Fields/25 Frames

Summary of Contents for SHC-721N

























Reviews: