Samsung SGH-X500 Page 25 Service Manual Download | Manualshive

Page: 25 / 62

background image

SAMSUNG Proprietary-Contents may change without notice

Disassembly and Assembly instructions

6-8

This Document can not be used without Samsung's authorization

10

9

■

LCD using consideration

- Please do not touch LCD both sides. (Seize side part )

- please don't give any impact to LCD ( finger or pincette)

- When you seize the corner of LCD , please don't give too much force.
- please don't touch LCD FPCB part.
- if there are any kinds of stain/air bubble/bow/dust, rinse LCD surface with Alcohol

and cotton stick.

- if there are any strange spots in LCD surface , please don't use those LCD.

those LCD are faulty LCD

- if there are any kinds of tear/split/demage/short in FPCB, please don't

use those LCD.

1) Following silk line, post 2 electric

conduction TAPE, please fold TAPE
following silk line .

※

caution

1) Do not go over MAIN LCD part.
2) Do not touch to insulation TAPE.
3) Be careful strange material or finger mark.

1) Post 2 sponge PORON following below

blue line.

※

caution

1) Be careful strange material or finger mark.

×

○

«
...
23
24
25
26
27
...
»

Summary of Contents for SGH-X500































































Reviews:

No comments

Related manuals for SGH-X500

Brand: Patton electronics Pages: 79

HTC Evo View 4G

Brand: HTC Pages: 42

Brand: Verykool Pages: 35

Brand: Plum Pages: 17

StrongPhone WiFi

Brand: Evolveo Pages: 9

Brand: Archos Pages: 180

Brand: Lemon Pages: 33

Brand: DSC Pages: 20

Brand: NGM Pages: 148

Brand: Zonda Pages: 21

Brand: Lava Pages: 25

Brand: Nokia Pages: 29

Brand: Zte Pages: 144

Brand: Avvio Pages: 30

Brand: Zte Pages: 172

Brand: Siemens Pages: 33

Brand: Samsung Pages: 37

Brand: Samsung Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands