manualshive.com logo in svg

Samsung S3F84B8, User Manual

The Samsung S3F84B8 user manual is available for free download on our website. This comprehensive manual provides detailed instructions, troubleshooting tips, and useful information to enhance your experience with this outstanding product. Get the most out of your Samsung S3F84B8 by downloading the user manual from manualshive.com.

Share
Download
background image

S3F84B8_UM_REV 1.00 

6 INSTRUCTION SET 

 

 6-5 

 

6.2  FLAGS REGISTER (FLAGS) 

The flags register (FLAGS) contains eight bits that describe current status of the CPU operations. Four of these 
bits, FLAGS.7 to FLAGS.4, can be tested and used with conditional jump instructions; two other bits, FLAGS.3 
and FLAGS.2, are used for BCD arithmetic.   

The flags register (FLAGS) also contains a bit to indicate the status of fast interrupt processing (FLAGS.1) and a 
bank address status bit (FLAGS.0) to indicate whether bank 0 or bank 1 is currently being addressed. It can be set 
or reset by instructions as long as its outcome does not affect flags such as Load instruction.   

Logical and Arithmetic instructions such as AND, OR, XOR, ADD, and SUB can affect the FLAGS register. For 
example, the AND instruction updates the Zero, Sign, and Overflow flags based on the outcome of the AND 
instruction. If the AND instruction uses the FLAGS register as the destination, then two write will occur 
simultaneously to the Flags register, producing an unpredictable result. 

System Flags Register (FLAGS)

D5H, R/W

.7

.6

.5

.4

.3

.2

.1

.0

MSB

LSB

Bank address
status flag (BA)

Fast interrupt
status flag (FIS)

Half-carry flag (H)

Decimal adjust flag (D)

Carry flag (C)

Zero flag (Z)

Sign flag (S)

Overflow flag (V)

 

    

Figure 6-1      System Flags Register (FLAGS) 

Summary of Contents for S3F84B8



































































































































































































































































































































Reviews:

No comments

Related manuals for S3F84B8

Vacmaster VP800 User Manual preview
VP800
Brand: Vacmaster Pages: 24
Danby DWC040A3BSSDD Owner'S Use And Care Manual preview
DWC040A3BSSDD
Brand: Danby Pages: 36
OBH Nordica 8706 Instructions Of Use preview
8706
Brand: OBH Nordica Pages: 12
Zelmer 887 User Manual preview
887
Brand: Zelmer Pages: 34
Van Berkel International HOME LINE Series Instruction Manual preview
HOME LINE Series
Brand: Van Berkel International Pages: 36
Indesit KP9F96S Operating Instructions Manual preview
KP9F96S
Brand: Indesit Pages: 20
U-Line UHWC115SG01A User Manual & Service Manual preview
UHWC115SG01A
Brand: U-Line Pages: 47
Magic mill MFD-6060 Instruction Manual preview
MFD-6060
Brand: Magic mill Pages: 20
AGA Falcon 110 Gas User'S Manual And Installation Instructions preview
Falcon 110 Gas
Brand: AGA Pages: 40
Hyundai SM627 Instruction Manual preview
SM627
Brand: Hyundai Pages: 44
Telstar TSE041920FH User Manual preview
TSE041920FH
Brand: Telstar Pages: 12
Cookworks 3 BOWL STEAMER Instruction Manual preview
3 BOWL STEAMER
Brand: Cookworks Pages: 16
Zelmer ZMM3501B User Manual preview
ZMM3501B
Brand: Zelmer Pages: 68
Coline MC0135 Instruction Manual preview
MC0135
Brand: Coline Pages: 20
Gastroversum FKG 261 Instructions For Use Manual preview
FKG 261
Brand: Gastroversum Pages: 7
Rangemaster RMB45SDBL/SS User Manual & Installation & Service Instructions preview
RMB45SDBL/SS
Brand: Rangemaster Pages: 8
STX International Activation 420 Instructions Manual preview
Activation 420
Brand: STX International Pages: 12
Laser Eezee's Muncheez Microwave Toastie Maker User Manual preview
Eezee's Muncheez Microwave Toastie Maker
Brand: Laser Pages: 10

Brands by name

Popular brands

Load more brands