Samsung ProXpress M4030 Series Service Manual Download Page 83

Page: 83 / 178

4. Troubleshooting

4. Troubleshooting

4.1. Control panel

Display screen

Shows the current status and prompts during an operation.

Back

Sends you back to the upper menu level.

Confirms the selection on the screen.

Numeric keypad

Use the keypad to enter numbers and characters.

Stop/ Clear

Stops current operation.

Power/ Wake Up

You can turn the power on and off with this button. Or wake up from the
power save mode.

Status LED

Indicates the status of your machine.

Demo Page

Prints a demo page by pressing this button.

Eco

Turn on the Eco mode to reduce toner consumption and paper usage.

Arrow

Navigates available values by moving to the next or previous options.

Enters menu mode and scrolls through the available menus.

4-1

Summary of Contents for ProXpress M4030 Series














































































































































































Search results

Summary of Contents for ProXpress M4030 Series

Reviews:

Brands by name

Popular brands

Samsung ProXpress M4030 Series, Service Manual

Search results

Summary of Contents for ProXpress M4030 Series

Reviews:

Brands by name

Popular brands