41
CUSTOMIZING YOUR KEYSET
AME PASSWORD
This feature allows people using the AME feature to enable password protection.
This will prevent unauthorized people from listening to your messages being left.
The passcode is the same as your station passcode. This feature only applies if
there is an SVM card installed in the system and your keyset has a programmed
AME key.
•
With the handset on-hook, press
TRANSFER
and then dial
110
.
•
Dial
101
to turn on AME PASSCODE or
100
to turn it off.
•
Press
TRANSFER
to store your selection.
AUTO CAMP-ON
This option allows intercom calls to be automatically camped on, if possible, when
a busy station is called.
•
With the handset on-hook, press
TRANSFER
and then dial
110
.
•
Press
081
to turn CAMP-ON on or
080
to turn it off.
•
Press
TRANSFER
to store your selection.
SELECT RING TONE
Each keyset user can select any one of eight ring frequencies:
•
While on-hook, press
TRANSFER
and then dial
111
.
•
Dial
1
–
8
or press the
UP
and
DOWN
keys to hear each tone.
•
When you hear the tone that you prefer, press
TRANSFER
to save it.
NOTE: Specific lines or stations may be programmed to ring with a different
tone than what you have selected for your keyset.
CHANGE YOUR PASSCODE
From the factory, your station passcode is 1234. You can change your station pass-
code whenever you desire.
•
While on-hook, press
TRANSFER
and then dial
101
.
•
Dial your old passcode.
•
Dial a new passcode (must be four characters). You can use
0
–
9
.
•
Redial the new passcode to verify. If successful, you will hear two beeps. Four
beeps indicate an incorrect code. Reenter the code again.
•
Press
TRANSFER
to store the new passcode.
the conversation through the AOM may possibly be heard by the caller on the
keyset. When you receive an executive OHVA through your AOM:
•
Reply by speaking in the direction of the microphone in the AOM unit.
•
Adjust the volume with the
VOLUME
keys on the AOM unit.
•
Press the
SPK
key on the AOM to disconnect the announcing party.
NOTES:
1.
Executive off-hook voice announce can only be accomplished when an AOM
is attached to your phone.
2.
If the
MUTE
key on the AOM is lit, you must press the AOM’s
SPK
key to
answer the OHVA call.
OHVA BLOCK
Your keyset can be programmed with an OHVA Block (
BLOCK
) key. Pressing this
key will prevent anyone from making an OHVA to you until you press the button
again and cancel the blocking.
OHVA REJECT
Your keyset can be programmed with an OHVA Reject (
REJECT
) key. Pressing this
key while receiving an OHVA call will disconnect the voice announcing party and
return you to your original call.
IN GROUP/OUT OF GROUP
If your keyset is assigned to a station ring group, you can remove your keyset from
the group and then put it back in. While you are out of the group, you can receive
calls to your extension number but not calls to the group number. If you have an
IN/OUT
key with the group number assigned.
•
Press the
IN/OUT
key. It will light red when your keyset is in the group.
•
Press the
IN/OUT
key again to exit the group and turn the light off. Repeat as
necessary.
If you do not have an
IN/OUT
key:
•
Dial the
IN/OUT
access code number ________________, then the group
number, then
0
to exit the group or
1
to enter the group.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the hand-
set or press
SPEAKER
key.
The
IN/OUT
key can include an extender to indicate the specific group that this
key will affect. This means that if you are in multiple groups, you can decide for
which groups you will receive calls.
40
Home Page
iDCS Keyset
Table of Contents
