Samsung NP-M70 User Manual Download Page 1

Notices   i 

Notices

No part of this publication may be reproduced, stored in a retrieval system, or 
transmitted, in any form or by any means, mechanical photocopying, recording or 
otherwise, without the prior written permission of the manufacturer.

The information within this manual is subject to change without notice.

The manufacturer shall not be held liable for technical or editorial errors or omissions 
contained in herein; nor for incidental or consequential damages resulting from the

furnishing, performance or use of this material.

Microsoft Windows is a registered trademark of the Microsoft Corporation.

Product names mentioned herein are for identification purposes only, and may be 
trademarks and/or registered trademarks of their respective companies.

Macrovision Statement

If your computer has a DVD drive and an analog TV Out port, the following 
paragraph applies:

This product incorporates copyright protection technology that is protected by method 
claims of certain U.S. patents and other intellectual property rights owned by 
Macrovision Corporation and other rights owners. Use of this copyright protection 
technology must be authorized by Macrovision Corporation, and is intended for home 
and other limited viewing uses only unless otherwise authorized by Macrovision 
Corporation. Reverse engineering or disassembly is prohibited.

Copyright 2003 All rights are reserved

Summary of Contents for NP-M70




































































































































































































Reviews: