Samsung ME16A4021AB Installation Instructions Manual Download Page 8

Page: 8 / 20

Step-by-step installation guide

1. PLACEMENT OF THE MOUNTING PLATE

A. REMOVING THE

MICROWAVE OVEN FROM

THE CARTON/REMOVING

THE MOUNTING PLATE

. Remove the installation instructions, Exhaust

adaptor, filters, glass tray and the small

hardware bag. Do not remove the Styrofoam

protecting the front of the oven.

. Fold back all 4 carton flaps fully against carton

sides. Then carefully roll the oven and carton

over onto the top side. The oven should be

resting in the Styrofoam.

Carton

Styrofoam

. Pull the carton up and off the oven.

. Remove and properly discard plastic bags.

Screws

Mounting Plate

Screws

. Remove the 2 screws from the mounting plate.

This plate will be used as the rear wall template

and for mounting.

NOTE

: You will have to reuse two screws in original

loction of outcase after removing mounting plate.

B. FINDING THE WALL STUDS

Center

Wall Studs

. Find the studs, using one of the following

methods:

Stud finder–a magnetic device which locates

nails.

Use a hammer to tap lightly across the

mounting surface to find a solid sound. This

will indicate a stud location.

. After locating the stud(s), find the center by

probing the wall with a small nail to find the

edges of the stud. Then place a mark halfway

between the edges. The center of any adjacent

studs should be 16˝ or 24˝ from this mark.

. Draw a line down the center of the studs.

THE MICROWAVE MUST BE CONNECTED TO

AT LEAST ONE WALL STUD.

SMH8165_XAA_DE68-03587A-10_EN.indd 8

6/19/2019 3:44:30 PM

Summary of Contents for ME16A4021AB





















Search results

Summary of Contents for ME16A4021AB

Reviews:

Related manuals for ME16A4021AB

Brands by name

Popular brands

Samsung ME16A4021AB, Installation Instructions Manual

Search results

Summary of Contents for ME16A4021AB

Reviews:

Related manuals for ME16A4021AB

Brands by name

Popular brands