English - 11
Connecting the TV to a SBB or STB
ETH MODEM
TV Rear Panel
STB (SBB)
Data Cable
Connect the
DATA
port of the TV to the
ETH MODEM
port of the STB
(SBB) with the Data cable.
•
The
ETH MODEM
port name that you connect the Data Cable to
may differ depending on the SBB or STB type.
•
IR signals sent by the remote control to the TV or SBB / STB must
meet the following specification to use IR pass through function.
IR signal receiver specification
– Band pass filter center frequency:
37.9
㎑
– Carrier Frequency, Duty 50%
–
Minimum Burst Length (tburst): 12 pulses (316 us)
– Minimum Gap Time Between the burst (tburst gap): 16
pulses (422 us)
– Minimum Gap Time between the data commands (tpause):
25
㎳
List of Hospitality SI Vendors and compatible data
cables supplied with the TV
•
Confirm you are using the correct data cable for your SI vendor.
Refer to the code label on the data cables.
•
Contact your nearest dealer or your SI Vendor to buy the data
cable not included in the TV.
1
6
1
2
3
4
5
Confirm the code on the Code Label.
TV side
STB (SBB) side
Cable code
Pin assign
REMARK
BN39-02462A
(Color: BLACK)
TV SIDE
1: NC
2: RX
3: TX
4: IR
5: GND
STB (SBB) SIDE
P1
P2
3
1
5
2
6
3
1
4
2
5
1: IR
2: GND
3: NC
4: NC
5: RX
6: TX
RED
GREEN
WHITE
BLACK
YELLOW
SAMSUNG
and others
BN39-02461A
(Color: LIGHT
GRAY)
TV SIDE
1: CLK
2: RX
3: TX
4: IR
5: GND
P1
P2
6
1
5
2
3
3
1
4
2
5
1: IR
2: GND
3: TX
4: NC
5: RX
6: CLK
RED
GREEN
WHITE
BLACK
YELLOW
STB (SBB) SIDE
MTI
•
RX and TX notation is based on TV.
• Operation Specification of Data Cable(RJ12): RS232
Network Security Protocols
The TV only supports the following wireless network security
protocols:
•
Authentication Modes: WEP, WPAPSK, WPA2PSK
•
Encryption Types: WEP, TKIP, AES
In compliance with the Wi-Fi certification specifications, Samsung TVs
do not support WEP or TKIP security encryption in networks running
in the 802.11n mode.
If the wireless access point supports WPS (Wi-Fi Protected Setup),
you can connect the TV to your network using PBC (Push Button
Configuration) or a PIN (Personal Identification Number). WPS
automatically configures the SSID and WPA key settings.
Your Smart TV cannot connect to uncertified wireless access point.
Establishing a wired Internet connection
There are three main ways to connect the TV to your network using
cable, depending on your network setup. They are illustrated below:
The Modem Port on
the Wall
Modem Cable (Not Supplied)
LAN Cable (Not Supplied)
TV Rear Panel
External Modem
(ADSL / VDSL / Cable TV)
TV Rear Panel
The Modem Port on the Wall
Modem Cable
(Not Supplied)
LAN Cable
(Not Supplied)
LAN Cable
(Not Supplied)
External Modem
(ADSL / VDSL / Cable TV)
IP access point that
has a DHCP Server
TV Rear Panel
The LAN Port on the Wall
LAN Cable (Not Supplied)
•
The TV will not be able to connect to the Internet if your network
speed is below 10 Mbps.
•
To connect a LAN cable, use a CAT 7 (*STP type) cable for the
connection. (100/10 Mbps)
* Shielded Twisted Pair
