manualshive.com logo in svg

Samsung DVG45T6200 Series, User Manual, Page: 42 / 60

Share
Download
Samsung DVG45T6200 Series User Manual Download Page 42

Engl

ish

Operations

English

42

Cycle chart

NOTE

For best results, follow the load size recommendations for each dry cycle.
• 

 Large load: Fill the drum to about 3/4 full. Do not add items over this level as they need to tumble 

freely.

• 

 Medium load : Fill the drum to about 1/2 full.

• 

 Small load : Fill the drum with 3-5 items, not more than 1/4 full.

Cycle

Recommended items

Load size

Dry level

NORMAL

Cottons, work clothes, linens, mixed loads

Normal dry 

(Adjustable)

HEAVY DUTY

Heavy fabrics such as jeans, corduroys, heavy work clothes

Normal dry 

(Adjustable)

BEDDING

Bulky items such as blankets, sheets, comforters, pillows

Normal dry 

(Adjustable)

PERM PRESS

Shirts, synthetic fabrics, knits, wrinkle-free cottons, permanent 

press

Normal dry 

(Adjustable)

DELICATES

Underwear, blouses, lingerie

Normal dry 

(Adjustable)

STEAM SANITIZE

Bedding, curtains, children's clothing

Very dry (Not 

adjustable)

REFRESH

Shirts, trousers, comforters, pillows

-

QUICK DRY

Small loads

-

TIME DRY

Any load

-

AIR FLUFF

Foam,rubber, plastic

-

Untitled-18   42

2023-06-29( )     3:23:51

Summary of Contents for DVG45T6200 Series





























































Reviews:

No comments