manualshive.com logo in svg

Samsung DVE50A5405 Series, User Manual, Page: 43 / 68

Share
Download
Samsung DVE50A5405 Series User Manual Download Page 43

English 

43

 

Operations

10 

Adjust Time

You can change the set time in the Manual Dry cycles (

QUICK 

DRY

, 

TIME DRY

, 

AIR FLUFF

, and 

WRINKLE RELEASE

) and 

WRINKLE AWAY

. To change the cycle time, press   or   until 

the desired time is displayed.

11 

Smart Control

After connecting the Tumble Dryer to your home network using 
the SmartThings app, you can control or monitor the dryer 
remotely. When started, the Smart Control indicator blinks. The 
dryer enters waiting mode and waits for remote commands.

12 

Power

Press to turn on/turn off the dryer.

13 

Start/Pause (Hold 

to Start)

Press to start or stop operation.

NOTE

Do not take extremely tangled items from your washer and put them into the dryer. They 
can degrade the drying efficiency of the dryer or cause the door to open. We recommend 
that you untangle the items before putting them into the dryer. Also, do not put objects on 
the dryer, especially on the control panel.

CAUTION

Do not spray water directly onto the control panel. This may cause a system failure.

Untitled-3   43

2021-02-02     3:23:27

Summary of Contents for DVE50A5405 Series





































































Reviews:

No comments