manualshive.com logo in svg

Samsung DVE47CG3500 Series, User Manual, Page: 40 / 60

Share
Download
Samsung DVE47CG3500 Series User Manual Download Page 40

Engl

ish

Operations

English

40

Manual Dry

You can change the drying settings manually to your preference.

Cycle

Description

QUICK DRY

A quick drying cycle running for 30 minutes.
The default cycle time is 30 minutes. However, you may manually change 
the cycle time if necessary.

TIME DRY

You can specify a cycle time in minutes.

WRINKLE RELEASE

The WRINKLE RELEASE cycle will release wrinkles from items that are 
clean, dry, and only slightly wrinkled, such as clothes from a crowded closet, 
suitcase or items that have been in the dryer too long after the cycle has 
ended. 

WRINKLE RELEASE

 can be used with any temperature selection.

Cycle chart

NOTE

For best results, follow the load size recommendations for each dry cycle.
• 

 Large load: Fill the drum to about 3/4 full. Do not add items over this level as they need to tumble 

freely.

• 

 Medium load : Fill the drum to about 1/2 full.

• 

 Small load : Fill the drum with 3-5 items, not more than 1/4 full.

Cycle

Recommended items

Load size

Dry level

Sensor Dry

NORMAL

Cottons, work clothes, linens, mixed loads

Normal dry 

(Adjustable)

HEAVY DUTY

Heavy Fabrics such as jeans, corduroys, heavy work 

clothes

Normal dry 

(Adjustable)

SANITIZE

Bedding, curtains, children’s clothing

Very Dry (Not 

adjustable)

BEDDING

Bulky items such as blankets, sheets, comforters, 

pillows

Normal dry 

(Adjustable)

PERM PRESS

Shirts, synthetic fabrics, knits, wrinkle-free cottons, 

permanent press

Normal dry 

(Adjustable)

DELICATES

Underwear, blouses, lingerie

Normal dry 

(Adjustable)

Manual Dry

TIME DRY

Any load

-

QUICK DRY

Small loads

-

WRINKLE RELEASE

Shirts, trousers, blouses

-

Untitled-30   40

2023-06-28( )     3:08:48

Summary of Contents for DVE47CG3500 Series





























































Reviews:

No comments