Samsung DS 24D User Instruction Download Page 53

Page: 53 / 131

OUTSIDE CALLS

MAKING AN OUTSIDE CALL

•

Lift the handset and press an idle outside line button, line group button
or dial a line access code to receive dial tone—

—press an idle out-

side line button, line group button or dial a line access code to receive
dial tone through the speaker—

—press

SPEAKER

, receive intercom

dial tone and dial a line access code.

•

Dial the telephone number.

•

Finish the call by replacing the handset or pressing the

ANS/RLS

key.

NOTE: You will receive No More Calls tone when you attempt to make a call
and there is no key available for that line.

•

If Least Cost Routing is enabled on your phone system, this button may
be labeled

LCR

or accessed by dialing an access code (usually

•

If your system is programmed to require an authorization code before
making a call, dial

plus a valid code before selecting a C.O. line.

•

If your system is programmed to require an account code before mak-
ing a call, press the

ACCT

button or dial

plus a valid bin number,

press the

ACCT

button again and then select a C.O. line.

For more information on authorization and account codes, see your system
administrator.

NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press the

SPEAKER

key before dialing.

ANSWERING AN OUTSIDE CALL

•

Lift the handset and you are automatically connected to the ringing call.

See

Ring Preference under Customizing Your Keyset

—

—press the

ANS/RLS

key to automatically answer on the speakerphone.

NOTE: If a call is flashing at your keyset but not ringing, you must press the
flashing button to answer.

UNIVERSAL ANSWER

Outside lines may be programmed to ring a general alerting device. To
answer calls ringing this device, dial

or press the

key. This device can

operate in any one of the six different ring plans.

NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press the

SPEAKER

key before dialing.

ADDING AN

iDCS 14 BUTTON KEY STRIP

•

Place the keyset face down on a flat surface.

•

Remove the base pedestal by placing your thumbs over the attachment
clips and press outward while simultaneously pressing down on the
keyset body with your fingertips.

•

Remove the ribbon cable knockout from the bottom of the keyset.

•

Clip the 14 button strip to the side of the keyset.

•

Plug one end of the ribbon cable into the keyset and the other end into
the 14 button strip.

•

Place the support bracket over the ribbon cable and secure with the six
screws provided.

•

Reattach the base pedestal.

REMOVE KNOCKOUTS

CONNECT RIBBON CABLE

Home Page

Table of Contents

iDCS Keyset

Summary of Contents for DS 24D




































































































































Search results

Summary of Contents for DS 24D

Reviews:

Related manuals for DS 24D

Brands by name

Popular brands

Samsung DS 24D, User Instruction

Search results

Summary of Contents for DS 24D

Reviews:

Related manuals for DS 24D

Brands by name

Popular brands