Samsung CLX-9251 Series Service Manual Download Page 159

Page: 159 / 481

3. Disassembly and Reassembly

3.3.23. Fuser unit

Open the side cover.

Remove the fuser unit after removing 2 screws.

Remove the Frame-Fuser Front[A] after removing 3
screws.

Remove the Frame-Fuser Rear[B] after removing 3
screws.

Remove the Fuser-Guide Duplex[C] after removing 3
screws.

Remove the Fuser-Bracket Top after removing 5 screws.

3-37

Summary of Contents for CLX-9251 Series

























































































































































































































































































































































































































































































Search results

Summary of Contents for CLX-9251 Series

Reviews:

Related manuals for CLX-9251 Series

Brands by name

Popular brands

Samsung CLX-9251 Series, Service Manual

Search results

Summary of Contents for CLX-9251 Series

Reviews:

Related manuals for CLX-9251 Series

Brands by name

Popular brands