background image

 
The product firmware can be upgraded by downloading the updated file from the following Web site:  

http://www.samsung-ODD.com

 

http://www.samsungelectronics.com/odd

 

 

 

 
Before you install the COMBO drive, we strongly recommend that you check that your setup meets the system 
requirements listed below. 

 

 

System Requirements

Item

Description

Computer

Intel Pentium II 400MHz/Celeron 466A(or higher), 64 MB of RAM (or higher) with an 
80pin IDE interface for Ultra DMA.

Free expansion unit

5.25 inch

Disk space

700 MB minimum

Windows version

Windows 98/2000/ME/XP/NT4.0 (or higher) 
(For Windows NT, we recommend Service Pack2, and Version is over 4.00.1381)

MS-DOS

5.0 or higher (For MS-DOS, The CD-R/CD-RW driver can only read a disc without 
premaster Software.)

DVD Video playback

PC with Windows 98/2000/ME/XP/NT4.0 DVD-Video playback software and 
appropriate hardware (the Power DVD MPEG software is included in the COMBO 
drive package)

DVD Region Protection Coding (RPC):

 
The RPC feature is supported on DVD players and is used with DVD-video discs (such as movies). Currently, 
the motionpicture industry has divided the worldinto different regions or zones thatcorrespond to the regional 
markets intowhich the motion picture industry releasesmovies. Simply put, RPC codes are placedon movies 
marketed throughout the world,based on the region of the world inwhich they are being sold. These 
RPCcodes help control and prevent piratingof new movies into other motion pictureregions prior to their true 
releasedates within those markets.  
The SM-348 COMBO drive supports RPCphase II. In the RPC-2 mode, the localcode can be changed by 
users. RPC-2is selected by default for the SM-348 COMBO drive. 
You can change the region code up tofive times via an MPEG application. 
 
Please contact your dealer or local SAMSUNG representative if you wish tochange the local code more than 
fivetimes. 

Upgrading the Firmware Flash Memory

Using the Drive

English - 14

Summary of Contents for CD Player



















Reviews: