background image

EB 2534 EN 

 15

Design and principle of operation

Table 3: 

K

VS

 coefficients and max. permissible differential pressures Δp

Valve size

K

VS

 coefficients

Max. permissible differential pressures Δp

Standard version

Special version

Standard version

Special version

DN 15

4.0

1 · 2.5

10 bar

14 bar

DN 20

6.3

DN 25

8.0

DN 32

16.0

10.0

8 bar

10 bar

DN 40

20.0

4 bar

DN 50

32.0

16.0

8 bar

Table 4: 

Dimensions in mm and weights in kg

Valve size

DN 15

DN 20

DN 25

DN 32

DN 40

DN 50

Regulator dimensions

Length L

130 mm

150 mm

160 mm

180 mm

200 mm

230 mm

Height H

560 mm

575 mm

Height H1

55 mm

72 mm

Set point r

anges

Actuator housing

0.8 to 2.5 bar

ØD = 225 mm, A = 160 cm²

1.2 to 3.5 bar

ØD = 225 mm, A = 160 cm²

2.0 to 5.0 bar

ØD = 170 mm, A = 160 cm²

2.4 to 6.3 bar

ØD = 170 mm, A = 80 cm²

4.5 to 10.0 bar

ØD = 170 mm, A = 80 cm²

8.0 to 16.0 bar

ØD = 170 mm, A = 40 cm²

Weight 

1)

, approx. kg

19

20

20

23

26

29

1) 

The weights are based on the weight of the regulator with actuator area A = 80 cm². Add 4 kg for A = 160 cm².

Summary of Contents for 2373









































Reviews: