Sammic UX-40, User Manual

Page: 13 / 60

Disposal
User’s manual — 2900455/0 13
EN
To install adjustable detergent dispensers, proceed as follows:
1) Access to the DD power strip on the lower front part of the
machine for the electrical connection of the soap dispenser.
This strip is controlled by solenoid valve EV1. Refer to the wiring
diagram for the correct connection order.
2) Install the soap injection fitting through the hole at the rear.
Rinse aid dispenser
Mains water dispenser
1) Check that the rinse aid tank is full.
2) Start the machine and stop the wash/rinse cycle 5 or 6 times by
successively pressing the PROG button , checking that the
rinse aid pipe fills up and the rinse aid enters the boiler.
⇒ The rinse aid can be adjusted using the adjustment screw on
the lower front part in the direction indicated.
Peristaltic dispenser
• The dose is adjusted in the settings section of the control panel.
[ ▶ p. 7 ]
• During installation, prime the detergent pipe from the settings
section [ ▶ p. 7 ].
• To check if the dose of rinse aid is effective, hold the glasses up
to the light.
– If there are drops of water on the glass, the dose is insufficient
– If there are streaks on the glass, the dose is too high.
Installation with descaler
Install a Sammic descaler when the limescale content in the
machine feed water exceeds 10 °fH (French grade).
• Installation instructions are supplied with the descaler.
• Avoid flow reductions (choking) before and after installation, as
they cause pressure losses.
Installation with back-up valve
Install a back-up valve when the water pressure to be supplied to
the machine is lower than the pressure specified for that model.
• The back-up valve can be installed at any point near the unit,
extending the water line and stopcock to the back-up valve.
• Make sure that the stopcock is still accessible.
• Connect one end of the back-up valve to the stopcock and the
other end to the hose supplied with the machine.
5 Disposal
Packaging
Follow current environmental standards in your country to dispose
of the packaging.
Machine
This machine is subject to the provisions of Euro -
pean Directive 2012/19/EU on waste electrical and
electronic equipment. The machine is marked with
the WEEE ( Waste of Electrical and Electronic
Equipment) symbol:
⭆ Do not dispose of this machine in normal house -
hold waste.
⭆ Dispose of the machine at an authorised waste management
centre or through municipal waste disposal entities. Comply
with the applicable regulations.
You can obtain information about waste disposal and the location
of your nearest recycling centre, for example, from your municipal
cleaning service.
6 Technical specifications
Front glasswashers and dishwashers
ℹ
Information
Sammic declines all liability for defects caused by faulty con -
nections when installing the dispensers.
Specifications UX 40
Glasswasher
UX 50 Lite
Front
UX 50
Front
Basket dimensions [mm] 400 x 400 500 x 500
Maximum crockery
height
300 mm 365 mm
Provision of baskets 2
Cycle [s] 90/120/
150/180
90/110/120/180/240
Basket production/h 40/30/24/20 40/33/30/20/15
Electrical power supply 230 V/50 Hz/ ∼ 1 400 V/50 Hz/ ∼ 3
Electric power
Motor pump 250 W/0.33 HP 750 W/1 HP
Washing power 1,200 W 1,800 W
Boiler power 2,800 W 3,000 W 5,000 W
Total power 3,050 W 3,750 W 5,750 W
Temperatures
Washing 40-7 0 °C (104-15 8 °F)
65-87 °C (149-189 °F) Rinse
Water capacity
Wash tank 9.0 L 14.0 L
Rinse boiler 4.5 L 8.0 L
Water consumption
(2 bar)
1.9 L 2.5 L
External Dimensions
Width [mm] 470 (490 [*])
[*] [S models with double wall]
580 (600 [*])
Depth [mm] 535 635
Height [mm] 710 830