SAMES KREMLIN FPro G Original Manual Download Page 28

Page: 28 / 92

Technical specifications and performance

5.1

Technical specifications

FPro G CONV - FPro G CONV GSP

FPro G CONV

FPro G CONV GSP

Type

Gravity

Maximum air supply pressure (network)

6 bar

Maximum product feed pressure

1 bar

Air flow rate

23, 8m3/h

23,3m3/h

Air pressure at the handle

Weight with cup

619 g

728 g

Weight without cup

446 g

527 g

Noise level

83 dBA

Maximum ambient operating temperature

50°C

FPro G HVLP - FPro G LVLP

FPro G HVLP

FPro G LVLP

Type

Gravity

Maximum air supply pressure (network)

6 bar

Maximum product feed pressure

Air flow rate

21.3 m3/h

14.9 m3/h

Air pressure at the handle

2.5 bar

Weight with cup

628 g

Weight without cup

455 g

Noise level

81 dBA

Maximum ambient operating temperature

50°C

Summary of Contents for FPro G





























































































Search results

Summary of Contents for FPro G

Reviews:

Related manuals for FPro G

Brands by name

Popular brands

SAMES KREMLIN FPro G, Original Manual

Search results

Summary of Contents for FPro G

Reviews:

Related manuals for FPro G

Brands by name

Popular brands