SAMES KREMLIN 64350225130000 Page 173 User Manual Download

Page: 173 / 238

Operations Dismantling / Reassembling the C225 Fluid section

582108110-EN-indG-Pompe Azur-52C225.docx

173

Operations Dismantling / Reassembling the C225 Fluid section

Drain the pump, cane or hopper.

Note: It is possible to stop feeding the hopper by the valve.
Note: Do not close the valve (1) while the pump is running.

Solvent the recirculating pump with solvent, using the
filter valve and the 1.5 m hose (option), and drain the
pump.

In case of replacement of the hopper strainer:



Lift the hopper lid and manually pull out the
strainer.

In case of replacement of the cane strainer:



unscrew the strainer manually and replace it

Summary of Contents for 64350225130000















































































































































































































































Search results

Summary of Contents for 64350225130000

Reviews:

Related manuals for 64350225130000

Brands by name

Popular brands

SAMES KREMLIN 64350225130000, User Manual

Search results

Summary of Contents for 64350225130000

Reviews:

Related manuals for 64350225130000

Brands by name

Popular brands