Sam Sirius 840 Page 31 User Manual Download

Page: 31 / 365

Sirius 800 Series User Manual

Software Compatibility Matrix

Product Overview 3.6

Iss 5 Rev 7

Page 31

3.6 Software Compatibility Matrix

3.6.1 Sirius 800 Routers

Table 2 states the compatibility between Sirius 800 router controller module versions and
SAM Workbench software releases.

Sirius 800

Router Controller Module

SAM Workbench

Software Release

2450
2462
2463

Up to 3.17.5

and

4.2 and above.

See

Note 1

and

Note 2

2464

4.0.3 and above.

See

Note 1

and

Note 2

Note 1: All

Sirius 800 router controllers will be supported by SAM Workbench

software release 4.2.x (not yet released, as of November 2016).

Note 2:

SAM Workbench software release 4.1.x is not yet available for general
release (as of November 2016).

Table 2

Sirius 800 Series Router Controller versus SAM Workbench Software Release

Summary of Contents for Sirius 840














































































































































































































































































































































































Search results

Summary of Contents for Sirius 840

Reviews:

Related manuals for Sirius 840

Brands by name

Popular brands

Sam Sirius 840, User Manual

Search results

Summary of Contents for Sirius 840

Reviews:

Related manuals for Sirius 840

Brands by name

Popular brands