Salus TRV10RFM Quick Manual Download Page 1

Note: 

If all valve dimensions are consistent with those given below, then the TRV 

head will be compatible. If there are dimension differences, contact us or the installer 

to find replacement for the valve.

Note: 

One thermostat can control up to 6 TRV heads within one room.

Quick Guide

Importer:

SALUS Controls plc

Salus House, Dodworth Business Park

Whinby Road, Barnsley S75 3SP, 

United Kingdom

DISTRIBUTOR OF SALUS CONTROLS:

QL CONTROLS Sp. z o.o., Sp. k.

Rolna 4, 

43-262 Kobielice, 
Poland

www.salus-controls.eu

SALUS Controls is a member of the Computime Group

Maintaining a policy of continuous product development SALUS 

Controls plc reserve the right to change specification, design and 

materials of products listed in this brochure without prior notice.

IV 2018

Introduction

The TRV thermostatic head is controlled through wireless ZigBee 

communication protocol. It can replace classic, manual thermostatic head in a 

very quick and easy way. For proper operation of the TRV head it is necessary 

to synchronize it correctly with wireless thermostat using the CO10RF 

coordinator or UGE600 Internet gateway (all devices are sold separately). TRV 

head paired with the iT600RF series digital thermostats (e.g. VS10RF / VS20RF 

/ HTRS-RF (30) / HTRP-RF (50) / TS600) provides comfort within the whole 

room, not just in the radiator area.

Product Compliance

This product complies with the essential requirements and other relevant 

provisions of Directives 2014/53/EU, 2014/30/EU, 2011/65/EU. The full text 

of the EU Declaration of Conformity is available at the following internet 

address: www.saluslegal.com.

           Safety Information

Use in accordance to national and EU regulations. Use the device as intended, 

keeping it in dry condition. Product for indoor use only. Installation must be 

carried out by a qualified person in accordance to national and EU regulations.

The TRV head is a modulating device. This means that the valve can be 

gradually closed or opened, depending on the  current room temperature 

measured by thermostat and the setpoint temperature.

For MMA or Herz M28x1,5 thermostatic valves make 

sure you have a metal washer as shown in the picture.

For a standard thermostatic valve with M30x1,5 

thread (e.g. Oventrop, Honeywell, TA, Heimeier) 

TRV10RFM head installation looks like as shown in 

the picture.

When mounting the TRV10RFM head on the Danfoss 

RA valve (see picture), please use the RA adapter 

included with the head. However, to install the 

TRV10RAM head it is necessary to use the Allen 

Wrench key.

NOTE: 

For the Comap valve with M28 thread you do 

not need to mount a metal washer.

TRV head is compatible with most of the thermostatic valves available on 

the market, however, before installation, please check whether the valve is 

suitable for use with the TRV head.

Put the RA 

adapter on the 

Danfoss RA 

valve.

Place TRV 

head on the 

valve.

Tight RA 

adapter 

and screw 

TRV10RFM 

head on it.

Assembly to 

the valve and 

tighten only 

2 out of 4 

screws.

Measure the thread diameter.

Thread for the TRV10RFM must 

have a diameter of 30 mm, and for 

the TRV28RFM - 28 mm.

Remove the battery cover located on 

the side of the device.

When the LED diode lights up 

continuously with a 

red

 color, 

screw the TRV on the valve.

When the LED goes out and TRV 

head does not make any sounds, 

adaptation process is finished. 

Equipment is ready for pairing 

with thermostat.

Press any button to start the 

adaptation process of TRV head with 

thermostatic valve. The process takes 

up to 5 minutes.

Insert the batteries according to the 

markings and close the battery cover.

The LED will start blinking 

green

 / 

red

 informing about the software 

version.

Measure the height of the valve’s 

pin when it is in the open position. 

For TRV10RFM valve’s pin height 

should be 13-15 mm, while for 

TRV28RFM 10-11 mm.

dismantle the old radiator 

head

radiator 

valve

To achieve the best possible results in cooperation between the thermostat 

and the heating source, it is recommended to use the RX10RF receiver. 

RX10RF turns on the heat source depending on the demand signal sent by 

thermostat. More informations about RX10RF receiver is included in its user 

manual.

1

2

3

4

Opening the head / indication  

of the device status

Closing the head / indication  

vof the device status

Pairing button

LED diode (indicates device status)

Box Content

TRV28RFM head installation

User interface

Buttons function

TRV10RFM head installation

TRV head setup

TRV head installation on the Danfoss RA valve

General informations

Checking compatibility with the heating system

TRV10RFM

adapter

Manual 

instruction

2 x AA batteries

metal

 washer

Allen Wrench key

TRV10RFM

Each box additionally contains:

TRV28RFM

TRV10RAM

TRV28RFM

TRV10RAM

+

+

OR

1

2

mm

10

20

30

3

mm

10

20

30

40

50

TRV10RFM

 HEAD MOUNTING

TRV10RAM

 HEAD MOUNTING

1

2

3

4

5

6

To do this...

Press the...

...pair with thermostat

...pairing button           for 10 seconds.

...lock/unlock the buttons

...pairing          and close           buttons together 

for 5 seconds.

...manually open the valve

...opening button           for 5 seconds.

...manually close the valve

...closing button           for 5 seconds.

...enter the automatic mode

...shortly pairing button             

...remove the head from the 

ZigBee network

...pairing button           for 10 seconds

...restore factory default settings

...Open          , pairing         , and close              

buttons together for 5 seconds

Wireless, thermostatic TRV head

Manual for models: TRV10RFM, TRV10RAM i TRV28RFM

Note: 

Buttons lock itself automatically after 5 minutes from the last one keystroke.

Reviews: