KL10
Installation and wiring guide
www.salus-controls.com Technical Helpline 00000 000000
Maintaining a policy of continued product development SALUS Controls plc reserve the right to change
specification, design and materials of products listed on this installation guide without prior notice.
Issue Date: June 2014 Document Number 00105
SL
L
N
1
2
+
HOT WATER TIMER
MODEL VS10W
ROOM THERMOSTAT PRT
MODEL VS10W
THERMOSTAT
MODEL VS10W
GROUP 2
THERMOSTAT
GROUP 2
THERMOSTAT
GROUP 2
DIAL THERMOSTAT
GROUP 1
DIAL THERMOSTAT
GROUP 1 CONTROL
THERMOSTAT
OPTIONAL UFH ZONE VALVE
FOR RADIATORS GROUPS
FUSE
FUSE
SUPPLIED CABLES
230V TO UFH PUMP
UNDERFLOOR HEATING MANIFOLD
1.5MM
2
CABLE (INSTALLER SUPPLIED)
1.5MM
2
CABLE (INSTALLER SUPPLIED)
1.5MM
2
CABLE
(INSTALLER SUPPLIED)
13 AMP FUSED CONNECTION UNIT
FUSED AT 3 AMPS
1.5MM
2
3 CORE
1.5MM
2
3 CORE
0.5MM
2
TWIN
ZONE 1
ZONE 1
HOT WATER
ZONE 2
ZONE 3
ZONE 4
ZONE 5
ZONE 6
ZONE 7
ZONE 8
SL N
L
SL N
L
SL N
L
SL N
L
SL N
L
SL N
L
SL N
L
GROUP 2
GROUP 1
N
L
+ +
+ +
+ +
+ +
-
-
-
-
SL
SL
N
L
ZONE 2
ZONE 3
ZONE 4
ZONE 5
ZONE 6
ZONE 7
ZONE 8
SL
L
N
1
2
SL
L
N
1
2
+
+
SL
L
N
1
2
+
SL
L
N
1
2
+
SL
L
N
1
2
+
SL
L
N
1
2
+
SL
L
N
1
2
+
1
2
+
OPTIONAL
PRT (RADIATORS
0.5MM
2
TWIN
L
N
L
N
L
N
L
N
L
N
L
N
L
N
L
N
L
N
L
N
L
N
L
N
L
N
L
N
L
N
L
N
SL
L
8
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
2
3
5
5
7
6
4
OUT
IN
1.5MM
2
CABLE
(INSTALLER SUPPLIED)
230V
OPTIONAL
CYLINDER STAT
1.5MM
2
CABLE
OUT
IN
(INSTALLER SUPPLIED)
COLOURS ARE INDICATIVE ONLY.
EXTRA CONNECTIONS MAY BE REQUIRED
AS PER MANUFACTURERS INSTRUCTIONS
1
IN
HW CYLINDER
THERMOSTAT
HEETING/
COOLING
FACTORY
FITTED
LINK
FACTORY
FITTED
LINK
FACTORY
FITTED
LINK
HW MOTORISED VALVE
OVERHEAT STAT
UFH PUMP
BOILER ENABLE
UFH MOTORISED VALVE
OUT
IN OUT
IN OUT
IN OUT
BR EA N OR GR
BR EA N OR GR
L N E
For PDF Installation guide please go to www.salus-controls.com
These instructions are applicable to the SALUS model
stated on the front cover of this manual only.
Warning
This product must be fitted by a competent person, and
installation must comply with the guidance, standards and
regulations applicable to the city, country or state where the
product is installed. Failure to comply with the requirements
of the relevant guidance, standards and regulations could lead
to injury, death or prosecution.
Warning
Always isolate the AC Mains supply before installing or working
on any components that require 230 VAC 50Hz supply.
9
Meets the following EC Directives
• Electro-Magntic Compatibility directive 2004 / 108 / EC
• Low voltage Directive 2006/95/EC
iT600 Wiring Centre KL10 005_Layout 1 05/06/2014 16:23 Page 1