background image

 

 

Installation and Operating 

Instructions 

 

 
 
 

 
 
 
 
 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Salamander Hobbit SE 

Model 0901 

Exempt under the Clean Air Act 1993 for use within 

UK Smoke Control Areas 

The  Hobbit

The  Hobbit

 

2

 
 

Installation and operating instructions for the Hobbit SE model 

0901 

(Ref 0901SE March 2013) 

 

 
      Section 

 

 

Contents    

               

Page 

 

1  

The Clean Air Act 1993 and Smoke   

 

  

Control 

Areas 

 

2  

Air Control modifications to assure smokeless 

  

operation 

 
3   

Important information about installing and 

using the Hobbit SE stove 

 

 

 

 

 

 

 

 

4  

Unpacking the Hobbit Stove  

 

 

5

 

 

5  

Assembly of the Hobbit Stove 

 

 

 

6  

Components of the Hobbit stove 

 

 

 

 Installation 

of 

the 

Hobbit 

   8 

 

 Operating 

instructions    9 

   

8.1   Fuel   

  

8.2   Before lighting 

   

8.3   Lighting a wood fire 

   

8.4   Re-fuelling 

   

8.5   De-ashing the stove  

 
9  

Guidance on safe operation   

 

          13 

 

10 

  Maintenance   

 

 

 

          14 

 

11 

Fault finding      

 

 

 

          15 

 
12 

Spare parts   

 

 

 

          15 

 

 

 

 
   

Summary of Contents for The Hobbit SE 0901









Reviews: