manualshive.com logo in svg

Sailor 6390, Installation Manual, Page: 49 / 61

Share
Download
Sailor 6390 Installation Manual Download Page 49

98-139768-A

A-1

Appendix A

AAAA

Technical specifications

Technical specifications

A

A.1

SAILOR 6390 Navtex Receiver

Item

Specification

Weight

1.3 kg

Dimensions 

L x W x H: 190 x 270 x 42.5 mm

Input voltage 

12-24 VDC (10.8 VDC to 31.2 VDC)

Power 
consumption

Typical 6.5 W

Heat dissipation

<10 W

Temperature

-15 °C to +55 °C (Operational) 
-15 °C to +55 °C (Storage)

Compass Safe 
Distance

20 cm (Standard magnetic compass) 
20 cm (Emergency magnetic compass)

IP rating

IP22 (estimated)

Navtex receivers

490 kHz, 518 kHz and 4209.5 kHz simultaneous 
reception.
Software updatable for 500 kHz NAVDAT 

Antenna support

Active and passive antenna (12 V @ 60 mA antenna 
supply)

Sensitivity
490/518 kHz

4209.5 kHz: 

<12 dB

V@10 

/150 pF

<-6 dB

V@50 

<12 dB

V@10 

/150 pF

<6 dB

V@50 

Interfaces

TNC antenna connector
Alarm relay output (normally closed)
2 LAN connectors
Remote on
NMEA0183 in and out for INS support
NMEA0183 in for e.g. GPS input
600 

 single ended audio interface for troubleshooting

Printer

Support via LAN connector

NMEA sentences

NMEA0183 input, EN61162-1: ACK, NRM, CRQ 
sentences
NMEA0183 output, EN61162-1: ALR, NRM, NRX 
sentences
GPS input: RMC, ZDA sentences
Proprietary sentences

Table A-1: SAILOR 6390 Navtex Receiver specifications 

Summary of Contents for 6390






























































Reviews:

No comments