Sailor 6390 Installation Manual Download Page 40 | Manualshive

Page: 40 / 61

Sailor 6390 Installation Manual Download Page 40

Verification

4-20

Chapter 4: Configuration

98-139768-A

4.4.4

Installation Tests

To run the available installation tests, do as follows:

1. Access the log-in page of the Service Interface, see

Using a PC and an Internet browser

2. Click

Installation tests.

• Click the button

Run Self Test

to run a Self Test of the SAILOR 6390 Navtex

Receiver.

• Click the button

Generate Test Message

to generate a Navtex test message. It is

displayed in the SAILOR 6004 Control Panel.

•

Change audio source

: The demodulated signal (1700 Hz +/-85 Hz) received on

518 kHz is always present for debug on connector J9. If a receiver is not performing
as expected, change the debug audio source to that receiver
(490 kHz/518 kHz/4209.5 kHz) and listen for e.g. a constant tone, indicating a
spurious on that receiver channel. The presence of a constant tone can then be
compared to the RF reception level measurements (see 4.4.3).
Note that changing the audio source is not saved to memory. After reboot the
518 kHz channel is always selected.

• To toggle the Alarm Relay click

On

and

Off

to check the connected alarm system.

Note

Do not log in to the Service Interface! The installation tests can be run separately.

Figure 4-20: Tests for verifying the installation

Figure 4-21: Checking the audio source, spring-loaded terminal J9

J9

Rx audio

GND

«
...
38
39
40
41
42
...
»

Summary of Contents for 6390






























































Reviews:

No comments