manualshive.com logo in svg

Saia Burgess Controls PCD7.D412DTPF, Manual, Page: 45 / 73

Share
Download
Saia Burgess Controls PCD7.D412DTPF Manual Download Page 45

Saia-Burgess Controls AG

Manual PCD7.D412DTPF & PCD7.D4xxxT5F │ Document 27-620 – Release ENG07 │ 2019-06-20

7-1

Updating and special settings

Firmware update

7

7 

Updating and special settings

7.1 

Firmware update

7.1.1 

Additional information on downloading FW

If problems occur while downloading via a USB connection, try the following 

solution:

Restart the MB panel with the USB cable REMOVED. Press the Download button 

and the MB panel’s Download mode is activated. Next, connect the USB cable to 

the MB panel and press Start in the FW Download Service Program.

If problems occur while downloading via a USB or ethernet connection, try the 

following solution:

If communications are interrupted during the download process, no notification 

appears on screen. This is because the FW flash memory is erased at the start of 

the process.

7.1.2 

Safe Firmware Download via USB

The safe method for downloading firmware is always via USB.

a) Switch off the MB panel

b) At the top of the back cover os a hole of 3 mm in diameter. It contains a button. 

Take a narrow-tipped pen or a small screwdriver (any cylindrical object with a 

diameter of 3 mm is suitable) and use it to hold down the button for short while. 

You can see the location of the Reset button in the figure:

c)  Switch on the MB panel with ON at the same time. Wait 3-4 sec. until the LED 

starts to flash. 

 

Then download the FW using the SBC FW Service Program.

CAUTION:  The *.blk file type is used for a complete FW file. Use only those 

files intended for the PCD7.D4xx panel and which were supplied 

by Saia Burgess Controls.

Summary of Contents for PCD7.D412DTPF










































































Reviews:

No comments