background image

 

SAFIRE 2400Di, 2600Di, 3200Di and 3600Di Diesel / fuel oil heaters 

4

 

 

USAGE, INSTALLATION AND MAINTENANCE 

 

 

January 2012 

SF_ Lämmitin Oy

 Tilhenkatu 1 20610 Turku Finland Puh/Fax +358(0)2-2443282 

 

 

USAGE 

 

BEFORE USING THE HEATER 

 

Before using the heater make sure that 

• the tank and the fuel hose are properly installed 

• the heater is properly attached to the mounting bracket 

• the combustion air, circulation air and exhaust can flow freely 

• there aren’t any foreign objects inside or near the heater or in its exhaust outlet, or substances which are 

flammable or can produce smells. 

 

Fuel 

 

The best fuel is winter grade light fuel oil, or off-road gas oil. If you can’t find winter grade fuel during the summer, 

you can use summer grade light fuel oil or paraffin oil. To remove condensation water, add about 2% isopropanol-

based antifreeze for gasoline engines (not antifreeze for diesel engines!) to the fuel. 

If you don’t use the heater in the winter and store it in a cold place, use paraffin oil the last time you use the 

heater, and leave the fuel hoses full (paraffin oil has a low cloud point). Paraffin oil will protect the hose from 

freeze. 

 

CONTROLLING THE HEATER AND INDICATOR LEDS 

 

Basic control panel  

 

Start: turn the switch to position “HEAT/ON”. 

Ventilation: turn the switch to position “VENT”. 

Turn off: turn the switch to position “OFF”. 

Adjust heating power, temperature (heaters with thermostat)  

or ventilation power (if the ventilating mode is active) with the  

adjustment knob. To obtain the normal room temperature,  

turn the adjustment knob to point upwards.  

 

 

 

 

 

 

 

GENIUS control panel 

Turn the heater on or off according to the instructions on the display. 

Return to the main menu with “BACK”-button. Scroll the main menu with  

arrow keys, choose an item with “OK”-button.  

NB!: After a power failure the time must be set again.  

 

 

 

 

 

SAFIRE 3000

 

SAFIRE

                 

BACK

OK

Hallinta

Ajastin

Asetukset

Termostaattin ytt

Made in Finland by 

SF-L mmitin Oy 

genius

 

Summary of Contents for 2400Di










Reviews: