background image

Model GIR911

Infrared Carbon Dioxide

NOVA-Sensor

D

ESIGN

 M

ANUAL

T h e   i n f o r m a t i o n   a n d   t e c h n i c a l   d a t a
d i s c l o s e d   b y   t h i s   d o c u m e n t   m a y   b e
u s e d   a n d   d i s s e m i n a t e d   o n l y   f o r   t h e
p u r p o s e s   a n d   t o   t h e   e x t e n t
s p e c i f i c a l l y   a u t h o r i z e d   b y   S

A F E T Y

S

Y S T E M S

  T

E C H N O L O G Y

  i n   w r i t i n g .   S u c h

i n f o r m a t i o n   a n d   t e c h n i c a l   d a t a   a r e
p r o p r i e t a r y   t o   S

A F E T Y

 

S

Y S T E M S

T

E C H N O L O G Y

  a n d   m a y   n o t   b e   u s e d   o r

d i s s e m i n a t e d   e x c e p t   a s   p r o v i d e d   i n   t h e
f o r e g o i n g   s e n t e n c e .

7 0 0 7 1

S

A F E T Y

  S

Y S T E M S

  T

E C H N O L O G Y

2 3 2 8 2   M i l l   C r e e k   D r i v e ,   S u i t e   2 1 5
L a g u n a   H i l l s ,   C a l i f o r n i a   9 2 6 5 3 ,       U S A
T e l   ( 9 4 9 ) 5 8 3 - 1 8 5 7       F a x   ( 9 0 9 ) 3 4 0 - 6 6 4 3
w w w . s a f e t y s y s . c o m

The information in this document is applicable to

sensors built on or after October, 2001

Summary of Contents for GIR911



















Reviews: