Pair Transmitter to Receiver
:
(Always test unit prior to
mounting
)
Th
e
transmitter works with the ERA-DCRX receiver & basic programming
calls for the user to pair the transmitters with a receiver
&
select a melody for
th
e
transmitter to instruct the receiver to play when triggered.
For quick setup, however, each zone defaults to a basic "ding-dong" sound allowing you to
easily pair the transmitter for a faster set up process.
Figure 1
Battery Installation
:
Changing the Zone Melody
:
By default, each zone is programmed by the factory to play the ding-dong
sound
1.
Hold down the "zone" button until you hear a short tone & all LEDs on
front panel of receiver are red (approx 3 seconds). The zone you are
programming will flash.
2.
Press the "volume" button to scroll through the 12 available melodies
for selection. Once you find a melody you like, move to step 3.
3.
Press the "
zone
" button to scroll to the next zone & repeat step 2 to
program a melody to other zones
.
4.
Once you have programmed a melody to all necessary zones,
move to
step
5
.
5.
Hold down the "
zone
" button until you hear a short tone sound
(approx
3 seconds) notifying the receiver is out of melody programming mode.
ERA-PBDCR
-STROBE
Owner’s Manual
This device complies with Part 15 of the FCC rules, Operation of this device is subject
to the following conditions: 1. This device may not cause harmful interference. 2. This
device must accept any interference, including interference that may cause unde-
sired operation.
Helpful Notes:
•
Each receiver is capable of pa
i
ring with
three
(
3
) transmitters per
zone.
•
Each zone features 1 x 12V DC output
.
The zone output will be used
to power the strobe included in th kit.
•
Output duration for the 12V DC output may be set to 5 sec, 10 sec, 1
min, & 2 min. The receiver features 1 x C-Form relay assignable to one
or multiple zones & will take on the duration of the 12V DC output.
•
Volume control: 4 levels plus mute, plus off.
•
Each transmitter must be paired to a zone on the receiver.
•
Each zone is programmed to the "ding-dong" sound from the factory.
•
When transmitter battery is low, it sends a signal to the receiver when
triggered & the corresponding LED on the receiver will continue to
flash for 10 minutes.
•
The ERA-PBTX is a push button transmitter that must be
programmed to a ERA compatible receiver to operated.
•
Push button measures 3.00'' H x 2.25'' W x 1.75'' D.
•
When triggered (center push button is pressed) the center halo
illuminates brightly for approximately 2 seconds.
•
The push button is outdoor rated and contains a silicone gasket to
keep moisture out. Mount with the small weep hole pointing down
to ensure any moisture in the unit evaporates out.
1.
On the ERA-DCRX receiver, hold down the "mode"
(left button in figure
3
below)
button until you hear a short tone sound & the "zone 1" LED flashes
(approx 3 sec)
.
2.
If you are programming the transmitter to zone 1
p
ress the button on your
transmitter. You will
h
ear the receiver play a short musical note (zone 1 will
continue to flash).
3.
To program a transmitter to a different zone, press the "zone" button on
the receiver to scroll to the appropriate zone . The zone you want to
program will flash. Repeat step 2 above.
4.
Once you have programmed all the zones move to the next step.
5.
To exit program mode, hold down the "mode" button until you hear a short
tone sound (approx 3 sec)
1.
Open the front cover by inserting the included screwdriver into the
square hole on the bottom of the unit (figure 1) & gently push & then
separate the top & bottom halves of the case.
2.
Remove top part of case from lower part of case (figure 2).
3.
Install the included CR2450A battery into the holder with positive (+) side
of the battery facing up (figure 2).
4.
Test the battery by pressing the center push. The green halo should
illuminate for approximately 2 seconds, signaling transmission. Note:
Program the push button to a compatible receiver PRIOR to mounting the
push
button.
Volume, Mute, Off:
The volume button on the side of the receiver controls the four different volume
levels, mutes & turns off the receiver. Pushing the volume button controls these
functions.
•
When all four zone LED lights are red, this indicates maximum volume
.
•
Three zone LED lights indicate the third volume level
.
•
Two zone LED lights indicate the second volume level
.
•
One zone LED light indicates the minimum volume level
.
•
No zone LED lights & a red power indicator light means the
Figure
3
What's in the Kit:
•
ERA-PBTX Wireless Push Button with Mounting Hardware/Double Sided
Tape
•
ERA-DCRX Desktop / Wall Mount Receiver
•
Strobe Light
•
Wire (if needed)
Figure
2
