Left Side Panel
1
1854-02
Right Side Panel
1
1854-03
Screw Post
18
HFFMFB
Left Cabinet Rail
1
1970-15
Pointed Screw
4
1902-23
Right Cabinet Rail
1
1970-16
Top Panel
1
1854-01
Back Panel
1
1854-04
Bottom Panel
1
1854-05
Locking Cam
18
HFFMFC
Wood Dowel
4
H8MMDWL
Half-Shelf
1
1854-07
Small Machine Screw
4
1854-28
Hinge Bracket (Style 1)
1
1854-29
Hinge Bracket (Style 2)
1
1854-30
Door
1
1854-08
Bushing
2
1854-31
Lock (2 Keys not shown)
1
1854-13
Large Nut
1
1854-24
Caster Bracket
4
1854-10
Barrel Nut
8
1854-23
Bolt
8
1854-27
Lock Washer
8
1854-21
Caster
4
8917-25
Shelf Peg
4
HSFBNZ
Adjustable Shelf
1
1854-06
Drawer
1
1854-09
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
AA
MODEL
NUMBER
1854
1854-37: 1 of 2; Rev. 1; 12/04
TOOLS REQUIRED: Phillips Screwdriver;
Hammer or Mallet
Machine Floor Stand
For questions or concerns, please call
Safco Consumer Hot Line 1-800-664-0042
available Monday-Friday 8:00 AM to 4:30 PM (Central Time)
(English-speaking operators)
ASSEMBLY INSTRUCTIONS
Safco Products Company, New Hope, MN 55428
LETTER
CODE
DESCRIPTION
QTY.
PART NO.
PARTS LIST
Q
Q
Q
Q
Q
D
Q
Q
Q
Q
Q
F
Properly identify the two rails
used!
The D Left Cabinet Rail is
stamped “CL” near the roller,
while the F Right Cabinet Rail is
stamped “CR”.
USE THIS HOLE
FOR FRONT
SCREW
1
Work on a smooth, clean surface.
Locate the A Left Side Panel and the B Right Side Panel and position them
with the holes up, as shown below. Insert C Screw Posts into the holes
along the top, back and bottom of each panel, and tighten with a screwdriver
(do not overtighten!)
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
A
Q
Q
Q
Q
Q
B
Attach the D Left
Cabinet Rail to the A
Left Side Panel, with the
roller facing the front
edge, using two E
Pointed Screws (start
with the hole closest to
the roller). Do the same
with the F Right
Cabinet Rail on the B
Right Side Panel.
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
C
Q
Q
Q
Q
Q
D
Q
Q
Q
Q
Q
E
Q
Q
Q
Q
Q
F
SLOT
SLOT
THROUGH HOLES
The G Top Panel has two finished edges, the H
Back Panel has no finished edges, and the I Bot-
tom Panel has one finished edge. Lay them down
with the large holes facing up. Insert six J Locking
Cams into each panel, with the arrows pointing toward
the nearest SIDE edge.
Insert the four K Wood Dowels into the holes in the
ends of the L Half-Shelf. Tap with a hammer or mallet
until they are fully seated.
Using two M Small Machine Screws each, attach the
N and O Hinge Brackets to the corners of the P
Door, opposite the large hole. Make sure that the
posts on the Brackets are closest to the corner. Slip a
Q Bushing over each post.
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
2
3
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
J
Q
Q
Q
Q
Q
FINISHED
EDGES
NO
FINISHED
EDGES
ONE
FINISHED
EDGE
Q
Q
Q
Q
Q
G
Q
Q
Q
Q
Q
H
Q
Q
Q
Q
Q
I
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
From the face of the
Door OPPOSITE the
screws in the Hinge
Brackets, insert the R
Lock through the large
hole, and fasten with
the S Large Nut so
that the pawl points
straight out to the
side. Once securely
fastened, turn the
Lock with the Key so
the pawl is parallel to
the edge.
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
P
Q
Q
Q
Q
Q
K
Q
Q
Q
Q
Q
L
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
N
Q
Q
Q
Q
Q
O
Q
Q
Q
Q
Q
M
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
R
Q
Q
Q
Q
Q
S
LOCK
PAWL
ASSEMBLED UNIT
MODEL 1854
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
A
Q
Q
Q
Q
Q
B
Q
Q
Q
Q
Q
C
Q
Q
Q
Q
Q
D
Q
Q
Q
Q
Q
E
Q
Q
Q
Q
Q
F
Q
Q
Q
Q
Q
G
Q
Q
Q
Q
Q
H
Q
Q
Q
Q
Q
I
Q
Q
Q
Q
Q
J
Q
Q
Q
Q
Q
K
Q
Q
Q
Q
Q
L
Q
Q
Q
Q
Q
M
Q
Q
Q
Q
Q
N
Q
Q
Q
Q
Q
O
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
P
Q
Q
Q
Q
Q
R
Q
Q
Q
Q
Q
S
Q
Q
Q
Q
Q
T
Q
Q
Q
Q
Q
V
Q
Q
Q
Q
Q
U
Q
Q
Q
Q
Q
X
Q
Q
Q
Q
Q
Y
Q
Q
Q
Q
Q
Z
Q
Q
Q
Q
Q
AA
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
W
