S+S Regeltechnik Rymaskon 200-Modbus Series, User Manual

Page: 20 / 55

RYM ASKON
®
200-Modbus
Modbus Slave User Manual
© S+S REGELTECHNIK GMBH
| THURN-UND-TAXIS-STR.22 | 90411 NÜRNBERG | GERMANY | FON +49(0)911 519470 | www.SplusS.de
Page 20 of 55
Register Name
Register
Address
Bit Position
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
change_flags_
set_points
3
0x0003
SP15
[0]
SP14
[0]
SP13
[0]
SP12
[0]
SP11
[0]
SP10
[0]
SP9
[0]
SP8
[0]
SP7
[0]
SP6
[0]
SP5
[0]
SP4
[0]
SP3
[0]
SP2
[0]
SP1
[0]
SP0
[0]
change_flags_
device_settings
4
0x0004
R
[0]
R
[0]
R
[0]
R
[0]
R
[0]
R
[0]
R
[0]
DS8
[0]
DS7
[0]
DS6
[0]
DS5
[0]
DS4
[0]
DS3
[0]
DS2
[0]
DS1
[0]
DS0
[0]
change_flags_
offset_values
5
0x0005
OV15
[0]
OV14
[0]
OV13
[0]
OV12
[0]
OV11
[0]
OV10
[0]
OV9
[0]
OV8
[0]
OV7
[0]
OV6
[0]
OV5
[0]
OV4
[0]
OV3
[0]
OV2
[0]
OV1
[0]
OV0
[0]
The change flag register states will remain true until the flags are cleared by the Modbus master by
writing a logical ‘1’ to the specific flag.
!!! Change flags can have the following binary values:
1 – true / 0 – false
!!! If a set point, device setting or offset value is changed by the user the corresponding flag will be set
and it has to be cleared by the Modbus master.
SP0 to SP15: change flags for set_point_0 to set_point_15 (see Table 31
on page 41)
DS0: change flag for modbus_parameter on register address 176 (see Table 18
on page 27)
DS1: change flag for pincode_system_administrator on register address 177 (see Table
19 on page 27)
DS2: change flag for pincode_end_user on register address 178 (see Table 19
on page 27)
DS3: change flag for lcd_color_red on register address 179 (see Table 20 on page
28)
DS4: change flag for lcd_color_green on register address 180 (see Table 20 on page
28)
DS5: change flag for lcd_color_blue on register address 181 (see Table 20 on page
28)
DS6: change flag for lcd_brightness_contrast on register address 182 (see Table 20
on page 28)
DS7: change flag for user_interface_settings on register address 183 (see Table 20
on page 28)
DS8: change flag for display_unit on register address 192 (see Table 21 on page
29)
OV0 to OV15: change flags for offset_value_0 to offset_value_15 (see
Table 34 on page 44)
Table 8: Change Flags
Register Name
Register
Adresse
Bit Position
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ir_remote_control_
command
32
0x0020
button_code
[0x00]
remote_id
[0x00]
This register provides the button_code and remote_id of a valid command received via the infrared
receiver. See Chapter 5 for detailed information.
!!! Whenever a command was received the ir_remote_control_command register is updated and the IRC
flag of the short_pressed register at address 1 is set (see Table 7 on Page 19).
Table 9: IR Remote Control Command