background image

 

 

Safety Warning 

Power Supply Safety Warning 

High leakage current, earth connection essential 

before connecting power supply.   

 

There is more than one power input. Be sure that all 

power cables are pulled out before you power down 

the system. 

 
Static Electricity Protection Warning 

Electrostatic sensitive device inside. Please wear the 

anti-ESD ring before handling.   

 
Laser Safety Warning 

CLASS 1 LASER PRODUCT 

Directly looking at the optical interfaces or fibers may 

damage your eyes. 

 
Serial Interface Safety Warning 

 

Hot-plugging in a serial interface may damage your 

terminal. Please power off the terminal before 

inserting a cable in the serial interface or pulling it 

out from the serial interface. 

 
Fan Safety Warning 

 

Heavy moving parts, guard against slide when 

plugging in or out. 

 
Transportation Safety Warning 

 

Weight may exceed 80KG. 

 

 

Don’t use this handle to lift the chassis. 

 

Maintenance Warning   

 

Users are not allowed to repair the parts within the 

device. Please contact qualified technical 

personnel if necessary. 

 

 

Summary of Contents for RG-S12000 Series

















Reviews: