Ruckus Wireless ICX 7150-24 Hardware Installation Manual Download Page 26

Page: 26 / 123

Shipping carton contents

When unpacking the device, verify that the contents of the shipping carton is complete. Save the shipping carton and packaging in the
event you need to return the shipment.

•

The Ruckus ICX 7150 device

•

An accessory kit containing the following items:

–

Rack mounting kit containing two L-shaped mounting brackets and two sets of eight sink-head screws (included only with
24-port and 48-port models)

–

Wall mounting kit containing two wall-mount screws and two plastic anchors (included only with ICX 7150-C12P)

–

Two-post rack kit containing four rack-mounting screws and four cage nuts (included only with 24-port and 48-port models)

–

Four rubber feet

–

One AC power cord, shielded (US only)

–

One power cord retainer clip

–

China-RoHS Hazardous/Toxic Substance statement

–

Read Me First document

Preparing for the Installation
Shipping carton contents

Ruckus ICX 7150 Switch Hardware Installation Guide

Part Number: 53-1004928-05

Summary of Contents for ICX 7150-24



























































































































Search results

Summary of Contents for ICX 7150-24

Reviews:

Brands by name

Popular brands

Ruckus Wireless ICX 7150-24, Hardware Installation Manual

Search results

Summary of Contents for ICX 7150-24

Reviews:

Brands by name

Popular brands