manualshive.com logo in svg

RTS LCP-100A, Operating Instructions Manual, Page: 12 / 31

Share
Download
RTS LCP-100A Operating Instructions Manual Download Page 12

☞

Tap CLR at any time to return to the normal incoming messages window display.

3.4

ASSIGNING SETUP PAGES

Each keypanel has 4 setup pages, and each setup page contains 16 key assignments. One setup page is assigned to
the main keypanel, and one is assigned to each expansion panel. Up to 3 expansion panels can therefore be con-
nected. Or, if less than 3 expansion panels are connected, the extra setup pages can be used as alternate configura-
tions for the main keypanel. This means that you can completely change the keypanel’s key assignments by
changing the setup page that is assigned. Assign setup pages as follows:

1. On the main keypanel, tap the E-PNL key.

12 KP96/KP97 Keypanel Operation Manual, Ver. 8.3G

NAME

DESCRIPTION

ID

Briefly displays the panel number of the keypanel (same as FUNC_DISPLAY_1).

LEV2

Briefly displays the level 2 talk key assignments (same as FUNC_DISPLAY_2).

LSTN

Briefly displays listen key assignments (same as FUNC_DISPLAY_3).

NAME

Gets a list of all crosspoints to this keypanel which are closed and displays the list in the incoming messages
window. (If there are no crosspoints closed “N/A” will briefly display.) Use the

↑↓

keys to scroll up or down

the list. You may press the incoming messages key to talk back to the selected crosspoint.

TYPE

Briefly displays the type of communication (point-to-point, party line etc.) for all level 1 talk key assignments.

MTX

Briefly displays the intercom system (matrix) names for all level 1 talk key assignments. If there is only one
intercom system, the word “LOCL” displays to indicate “local matrix”.

TONE

Turns on the keypanel’s tone generator (same as FUNC_DISPLAY_7). Tap CLR to turn the tone generator

off. (See Activating the Tone Generator, page 31.)

EPNL

Briefly displays the setup page numbers of the main keypanel and any connected expansion panels (same
as FUNC_DISPLAY_8).

V8.3G

Displays current software version. (The PGM key causes no further action.)

GAIN

Used to adjust listen gain for a point-to-point or party line listen key. After selecting GAIN, tap a listen key.
After a few seconds, the gain level for that key will display. Use the

↑↓

keys to change the gain level.

TEST

Enters test mode (same as FUNC_DISPLAY_0).

Table 1: Display Requests Using Scrolling

E-PNL

DISPLAY

8

Summary of Contents for LCP-100A
































Reviews:

No comments