background image

14

General information

Service

This product has been factory aligned and tested to specification 

before shipment. In normal circumstances, the transceiver will 

operate in accordance with these instructions. All adjustable trim-

mers, coils, and resistors in the transceiver were preset at the 

factory. They should only be readjusted by a qualified technician 

who is familiar with this transceiver and has the necessary test 

equipment. Attempting service or alignment without factory auth-

orization can void the transceiver warranty. 
When operated properly, the transceiver will provide years of service 

and enjoyment without requiring further realignment. The information 

in this section gives some general service procedures requiring little 

or no test equipment.

If it is ever necessary to return this equipment to your dealer or 

service center for repair, pack it in its original box and packing 

material. Include a full description of the problems experienced. 

Include your telephone number, fax number, and e-mail address (if 

available) along with your name and address in case the service 

technician needs to call you for further information While investi-

gating your problem. Do not return accessory items unless you feel 

they are directly related to the service problem.

You may return this product for service to the authorized 

 

dealer from whom you purchased it, or any authorized 

 

service center. A copy of the service report will be returned with the 

transceiver. Please do not send subassemblies or printed circuit 

boards; send the complete transceiver. Tag all returned items with 

your name and call sign for identification. 

Please mention the model and serial number of the transceiver in 

any communication regarding the problem.

MAINTENANCE

Service note

Cleaning

If you desire to correspond on a technical or operational problem, 

please make your note short, complete, and to the point. Help us 

help you by providing the following:

• 

Model and serial number of equipment.

• 

Question or problem you are having.

• 

Other equipment in your station pertaining to the problem.

• 

Meter readings.

• 

Other related information (menu setup, mode, frequency, key 

sequence to induce malfunction, etc.)

Do not pack the equipment in crushed newspapers for shipment. 
Extensive damage may result during rough handling or shipping.

The keys, controls, and case of the transceiver are likely to become 

soiled after extended use. Remove the controls from the transceiver 

and clean them with a neutral detergent and warm water. Use a 

neutral detergent (no strong chemicals) and a damp cloth to clean 

the case.

Warning:

Summary of Contents for DV 2055 Series























Reviews: