rtd DM35820HR Page 38 User Manual Download

Page: 38 / 82

RTD Embedded Technologies, Inc.

www.rtd.com

DMx820 User’s Manual

Field

Description

VERSION

FPGA Source Version Identifier

BOARD_RESET

Writing a value of 0xA5A5 to this register resets the board. All internal registers are set to their default values.

Note:

The 82C54 Timer/Counters are not affected by this register

RESET

W,+0000 0000 0000 0000

Field

Description

RESET

Write 0xA5A5 to reset the board. All other writes are

ignored. Reads will return all zeros.

BRD_STAT

This register contains status information for the board.

Reserved

MSTR

R,+0

R,+N

Field

Description

MSTR

Indicates if the board is PCI master capable based on the

rotary switch and jumper settings.
’0’ = PCI Master
’1’ = Not PCI Master

INT_ENABLE

This register controls which interrupt sources are used to generate a local interrupt.

FIFO1

FIFO0

PClk3

PClk2

PClk1

PClk0

PWM1

PWM0

RW,+0

Reserved

IncEnc1

IncEnc0

Rsvd

82C54

AdvInt1

AdvInt0

R,+00

RW,+0

R,+0

RW,+0

Field

Description

AdvInt0

Interrupt from Advance Interrupt block at 0x0200

’0’ = Interrupt Disabled
’1’ = Interrupt Enabled

AdvInt1

Interrupt from Advance Interrupt block at 0x0240

’0’ = Interrupt Disabled
’1’ = Interrupt Enabled

82C54

Interrupt 82C54 Timer/Counter block at 0x0080

’0’ = Interrupt Disabled
’1’ = Interrupt Enabled

Summary of Contents for DM35820HR



















































































Search results

Summary of Contents for DM35820HR

Reviews:

Related manuals for DM35820HR

Brands by name

Popular brands

rtd DM35820HR, User Manual

Search results

Summary of Contents for DM35820HR

Reviews:

Related manuals for DM35820HR

Brands by name

Popular brands