RTA 460BCUS-NNA1 Product User Manual Download Page 63

Page: 63 / 70

Real Time Automation, Inc.

1-800-249-1612

Diagnostics

– OPC UA Server

Select the OPC UA Server in the dropdown menu on the Diagnostics Page to view breakdown of the
diagnostics and common strings that are displayed on the page. Additional diagnostic information can
be found by clicking the

Help

button.

NOTE

: This page will auto-refresh every five seconds with the latest data.

Clear All Values

- This will only affect displayed values.

This will reset all displayed values back to zero and clear the Status Strings.

If viewing only the OPC UA Server section, this will only clear the values for the OPC UA Server
section of the gateway.

Device Status

Connected

–

An OPC UA client is connected and communicating to the gateway.

Not Connected

–

The gateway has not received any messages from an OPC UA client.

Error Timeout

–

The gateway has not received any messages from an OPC UA client within the

configured inactivity timeout.

LED Status:

Solid Green (Connected) -- An OPC UA client is connected and communicating to the gateway.

Flashing Green (Communication not yet attempted) -- The gateway has not received any
messages from an OPC UA client.

Flashing Red (Timeout)

The gateway has not received any messages within the configured

inactivity timeout.

Summary of Contents for 460BCUS-NNA1







































































Search results

Summary of Contents for 460BCUS-NNA1

Reviews:

Related manuals for 460BCUS-NNA1

Brands by name

Popular brands

RTA 460BCUS-NNA1, Product User Manual

Search results

Summary of Contents for 460BCUS-NNA1

Reviews:

Related manuals for 460BCUS-NNA1

Brands by name

Popular brands