VW2100 Vibrating Wire Piezometer
RST Instruments Ltd.
Page 34
R
EFERENCES
A-1
Terzaghi, K
and Peck, R.B.; “Soil Mechanics in Engineering Practice”, John Wiley and Sons,
Inc., 1967. (Article 68 of Chapter 12 provides a survey of tip types and recommendations on
installation procedure.)
A-2
U.S. Department of the Interior, Bureau of Reclamation
; “Earth Manual”, U.S. Government
Printing Office, Washington 1974. (Designations E-27 and E-28 in the Appendix give detailed
guidance on piezometer installations in dam foundations.)
A-3
Bishop, A.W., Vaughan, P.R., and Green, G.E. (1969); Report on speci
alty session, “Pore
Measurements in the Field and in the Laboratory”, Proc. 7th, Int. Conf. Soil Mech. and
Found. Eng. 3, 427. (A review of recent practice and instrumentation, related principally to
earth structures.)
A-4
“Suggested Methods for Determining In-Situ Permeability, Groundwater Pressure and Flow”;
Int. Soc. for Rock Mechanics, committee on Field Tests (Draft report, 1974; Final report in
course of preparation.)
A-5
Hanna, T.H.; “Foundation Instrumentation”, Trans. Tech. Publications, Ohio, USA, 1973.
(Chapter 3 describes different types of piezometer tip, methods of installation, methods of
recording and the protection of piezometer.)
A-6
Clements, D.J., and A.C. Durney (1982); “Instrumentation Developments”, Proceedings of
the Autumn Conference on the British National Committee on Large Dams (BNCOLD) Keele
University, Institution of Civil Engineers, London, pp. A5-55.
A-7
General Electric (1976); Transient voltage suppression manual, G.E. Semiconductor
products Department, Syracuse, New York.
A-8
Baker, C. (1978); “Surge Protection for Instrumentation”, proceedings of the Tempcon
Conference, London. Available from Measurement Technology, Inc., 7541 Gary Road,
Manassas, Virginia, 22110, U.S.A.
A-9
Baker, C., (1980); “Protecting Electronic Circuits from Lightening and Transients”. Available
from Measurement Technology, Inc., 7541 Gary Road, Manassas, Virginia, 22110, U.S.A.
A-10
Corps of Engineers (1984); “Publications Relating to Geotechnical Activities”, USACE
DAENECE-G, September 27th.
A-11
McKenna, G.T. (1995
); “Grouted-In Installation of Piezometers in Boreholes”, Canadian
Geotechnical Journal, Vol.32(2), pp. 355-263.
A-11
Mikkelsen, P.E. and Green, G.E. (2003); “Piezometers in fully grouted boreholes”. Field
Measurements in Geomechanics, -Myrvoll(ed.). Swets & Zeitlinger, Lisse, ISBN 90 5809
602 5.
A-12
Contreras, I.A., Grosser. A.T., Ver Strate, R.H. (2008); `The Use of the Fully-Grouted Method
for Piezometer Installations``, Geotechnical Instrumentation News, Episode 55
A-13
Contreras, I.A., Grosser. A.T., Ver Strate, R.H. (2011); `Practical Aspects of the Fully-
Grouted Method for Piezometer Installations``, Proc 8
th
International Symposium on Field
Measurements in Geomechanics, Berlin.
A-14
Simeoni, L., De Polo, F., Caloni, G., Pezzetti, G. (2011); Field Performance of Fully Grouted
Piezometers`, Proc 8
th
International Symposium on Field Measurements in Geomechanics,
Berlin.
A-15
Contreras, I.A., Grosser. A.T., Ver Strate, R.H. (2012); `Update of the Fully-Grouted Method
for Piezometer Installation``, Geotechnical Instrumentation News, Episode 70