manualshive.com logo in svg

RS PRO 917-6298, Instruction Manual

Share
Download
RS PRO 917-6298 Instruction Manual Download Page 57

 

IIT-2000/2010/5000/5010 Instruction Manual/English

 

05/08/2015 Version No. 001 

55

 

Hold the TIMER soft-key for 3 seconds to turn the 

timer off. 

I M E

T

R

 

 Note 

The timer can only be turned off under special MANU test 

mode, however there is a limitation:  

The timer cannot be turned off (limited to 240s) if the test 

current is between 30mA and 40mA (IIT-2000/2010) or 80mA 

and 100mA (IIT-5010/5000) in ACW mode.  

The discharge time and initial test time cannot be edited.  

Setting the Ramp Up Time 

 

Background 

The Ramp Up time is the total time taken for the tester to 

reach the test voltage level. The Ramp Up time starts after the 

initial time (approximately 150ms) with a start voltage of 50 

volts. The Ramp Up time can be set from 000.1 to 999.9 

seconds. The Ramp Up time is only applicable for ACW, DCW 

and IR tests. 

Discharge time 

Test V

time

Start V

Initial time

TEST TIME

RAMP

(Approximately 150ms)

  

Summary of Contents for 917-6298






























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands