manualshive.com logo in svg

RS PRO 205-0963, Operating Manual, Page: 18 / 24

Share
Download
RS PRO 205-0963 Operating Manual Download Page 18

page 18 of 24 

Operating Manual RS 1107, RS 1113 

 

rspro.com

 

_ 

 

 

NOTE 

 

This symbol indicates processes, which can have a direct influence on operation or 
can trigger an unforeseen reaction in case of non-observance. 

 

NOTE 

 

Read the following handling instructions before replacing batteries and follow them 
step by step.  
If disregarded, the product could be damaged or the protection from moisture could be 
diminished. 

 

 

1. 

Unscrews the Phillips screws (A)and remove the cover. 

2. 

Carefully replace the two Mignon AA batteries (B). En-
sure that the polarity is correct! It must be possible to in-
sert the batteries in the correct position without using 
force. 

3. 

The O-ring (C) must be undamaged, clean and posi-
tioned at the intended depth. In order to facilitate assem-
bly and avoid damage, a suitable grease can be applied. 

4. 

Fit the cover on evenly. The O-ring must remain at the 
intended depth! 

5. 

Tighten the Phillips screws (A). 

7 

Error and system messages 

 

Display

 

Meaning

 

Possible

 

causes

 

Remedy

 

----

 

Calculation not 
possible 

Measurement data 
acquisition is run-
ning 

Waiting for data collection 

 

 

 

Summary of Contents for 205-0963

























Reviews:

No comments