Royal Enfield Himalayan Service Manual Download Page 74

Page: 74 / 214

ROYAL ENFIELD HIMALAYAN BS III VEHICLE SERVICE MANUAL

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Assemble/

Instructions

10.2 Exhaust pipe &

Silencer



Locate a new gasket on

the exhaust pipe.



Locate exhaust pipe

into the cylinder head,

position the clamp over

the studs on the cylinder

head & assemble 2 hex

nuts M8

DO NOT

TIGHTEN FULLY.

Hex Nuts: M8X1.25
Socket spanner -12mm
Torque: 10Nm (1.0Kg.M.)

Hex bolts: M8 X 1.25X45
Hex Nuts: M8 X1.25
Socket spanner -12mm
Double End Spanner: 12mm
Torque: 25Nm (2.5Kg.M)



Position

silencer

mounting

bracket

against the frame at the

rear and insert flanged

hex bolt. Assemble hex

nut over bolt.



Tighten the 2 hex nuts at

the cylinder head, first

and then the silencer

bracket nut.

No.-

Summary of Contents for Himalayan























































































































































































































Search results

Summary of Contents for Himalayan

Reviews:

Royal Enfield Himalayan, Service Manual, Page: 74 / 214

Search results

Summary of Contents for Himalayan

Reviews: