manualshive.com logo in svg

Royal Enfield Himalayan, Service Manual, Page: 72 / 214

Share
Download
Royal Enfield Himalayan Service Manual Download Page 72

ROYAL ENFIELD    HIMALAYAN BS III VEHICLE SERVICE MANUAL

71

S.

No.

Fastener,  Size, Tool Usage, Precautions, Photos

Aggregate to Dismantle/

Instructions

10.1 Exhaust pipe &

Silencer

Remove 2 flanged Hex

nuts along with washers

at the cylinder head end.

Hex Nuts: M8X1.25
Socket spanner -12mm

Hex bolts: M8 X 1.25X45
Hex Nuts:  M8 X1.25
Socket spanner - 12mm
Double End Spanner: 12mm

NOTE:

Remove copper washer in

cylinder  head,  exhaust

pipe  seating  area  after

removing exhaust pipe.

Remove 2 Hex bolts &

nuts  at  the  silencer

mounting bracket end.

Support the silencer and

remove the bolt.

Gently  pull  out  the

exhaust pipe from the

cylinder  head  and

remove  exhaust  pipe

with silencer from the

vehicle.

Release the clamp from

the studs.

Summary of Contents for Himalayan























































































































































































































Reviews:

No comments