manualshive.com logo in svg

Royal Enfield Himalayan, Service Manual, Page: 171 / 214

Share
Download
Royal Enfield Himalayan Service Manual Download Page 171

ROYAL ENFIELD    HIMALAYAN BS III VEHICLE SERVICE MANUAL

170

14.3 Carburetor

internals

S.

No.

Fastener,  Size, Tool Usage, Precautions, Photos

Aggregate to Assemble /

Instructions

Locate float bowl along
with  rubber  ring  on

carburetor body

Ensure spring washers
are assembled on the 4

slotted head screws and
tighten 

bowl 

to

carburetor body.

Insert  piston  valve

assembly with diaphragm
rubber into the top bore
in carburetor body.

Assemble spring in the

piston valve assembly.

Position top cover over
the  spring,  gently

compress till the cover
rests  on  carburetor
body and the mounting

holes are aligned.

Tighten  cover to  body
with the three screws.

Assemble spring, washer,

inside  and  outside  O
rings on pilot air screw

Locate pilot air screw in

carburetor  body  and
gently  tighten  till
resistance  is  felt  and

screw 

cannot 

be

tightened further.

Loosen pilot air screw by

1 ½ TO 2 FULL TURNS.

NOTE:

Ensure  proper  seating  of

rubber ring in the groove in

float bowl.
Do not apply any adhesive

to seat the rubber ring.

Screw driver
Torque : 35 + 10 Kgf

NOTE:

Ensure the locating peg of

the diaphragm is correctly

and properly seated in the

carburetor body.

Screw driver
Torque : 35 + 10 Kgf

NOTE:

DO  NOT over  tighten  the

pilot screw as it will cause

damage to the pointed tip.

Summary of Contents for Himalayan























































































































































































































Reviews:

No comments