Royal Enfield Himalayan Service Manual Download Page 150

Page: 150 / 214

ROYAL ENFIELD HIMALAYAN BS III VEHICLE SERVICE MANUAL

149

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Assemble/

Instructions

13.3

Front Disc Brake



Assemble the rubber

Boot.

No.

.3.4

Master cylinder on

handle bar



Apply Silicon grease on

the Lever pivot hole and

on the Piston surface.



Position brake lever

inside the bracket, locate

pivot screw from the top

and tighten to bracket.



Assemble lock nut below

and tighten.

CAUTION:

Do not use tools with sharp

ends.



Locate the conical spring

on the piston, compress

and assemble Circlip into

the groove of the master

cylinder.

Hex Screw
Hex nut : M5
Screw driver
Spanner: 8mm
Torque: 6Nm(0.6 KgM)



Assemble the Brake

Switch on the bracket.



Connect the brake light

switch.

Summary of Contents for Himalayan























































































































































































































Search results

Summary of Contents for Himalayan

Reviews:

Royal Enfield Himalayan, Service Manual, Page: 150 / 214

Search results

Summary of Contents for Himalayan

Reviews: