manualshive.com logo in svg

Royal Enfield Himalayan, Service Manual, Page: 148 / 214

Share
Download
Royal Enfield Himalayan Service Manual Download Page 148

ROYAL ENFIELD    HIMALAYAN BS III VEHICLE SERVICE MANUAL

147

Fastener,  Size, Tool Usage, Precautions, Photos

Aggregate to Assemble/

Instructions

13.3

Front Disc Brake

Install brake pad on the

piston side first with its

friction material facing

outside.

Install the other brake

pad  with  the  friction

material  facing  the

opposite brake pad.

S.

No.

13.3

.2

Brake pads in

caliper

Apply Silicon grease on

the pin OD and assemble

the Pin bolt by pressing

gently  through  the

brake pads into caliper

body.

NOTE:

Ensure pads are  positioned

and locked correctly in the

mounting bracket lug.

Tighten the pins to the

caliper body.

Assemble Grub screws

on the pins and tighten.

Brake pad pins
Allen key: 5mm
Torque: 20Nm (2.0Kgm)

Grub screws
Screw driver
Torque: 3Nm (0.3Kgm)

Summary of Contents for Himalayan























































































































































































































Reviews:

No comments