Royal Enfield Bullet Classic EFI Service Manual Download Page 86

Page: 86 / 301

ROYAL ENFIELD VEHICLE SERVICE MANUAL - EURO IV

No.

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Dismantle/

Instructions

6.4 Front Fork

Dismantling



Pull in the inner tube on

the outer tube sharply

to locate the inner tube

along with the guide

bush, seat pipe assembly,

rebound spring and cap

oil lock.



Locate the dust seal,

retainer clip, and fork

seal in the outer tube.



Locate the special tool in

the inner tube.



Locate and install the

hex socket head nut

inside the outer tube.



Locate special tool

inside inner tube such

that it engages with the

nut on the seat pipe inside.



Locate the pinch bolt

and nut on Fork RH.

Special Tool: ST-25834-2
Allen Key: 10mm

Hex bolt & nut: M6
Ring spanners: 10mm

KS MOTORCYCLES - http://ksmotorcycles.com

Summary of Contents for Bullet Classic EFI














































































































































































































































































































Search results

Summary of Contents for Bullet Classic EFI

Reviews:

Royal Enfield Bullet Classic EFI, Service Manual, Page: 86 / 301

Search results

Summary of Contents for Bullet Classic EFI

Reviews: